Number of results to display per page
Search Results
152. Blob wakes in NSTX
- Author(s):
- Zweben SJ, Myra JR, Diallo A, Russell DA, Scotti F, Stotler DP
- Abstract:
- Transient small-scale structures were identified in the wake of blobs movingpoloidally through the SOL of high-powered H-mode plasmas in NSTX, using the gaspuff imaging (GPI) diagnostic. These blob wakes had a poloidal wavelength in therange 3.5 cm, which is significantly smaller than the average blob scale of~12 cm, and the wakes had a poloidal velocity of 1.5 km/sec in theelectron diamagnetic direction, which is opposite to the blob poloidal velocity inthese shots. These wakes were radially localized 0-4 cm outside the separatrix andoccurred within ~50 microsec after the passage of a blob through the GPI field of view.The clearest wakes were seen when the GPI viewing angle was well aligned with thelocal B field line, as expected for such small-scale structures given the diagnosticgeometry. A plausible theoretical interpretation of the wakes is discussed: theobserved wakes share some features of drift waves and/or drift-Alfven waves whichcould be excited
- Type:
- Dataset
- Issue Date:
- July 2019
153. Bubble pinch-off in turbulence
- Abstract:
- Experimental data, simulation code, and Python scripts to reproduce the data presented in "Bubble pinch-off in turbulence"
- Type:
- Dataset and Software
154. Calibrated VIC Model Parameters over CONUS
- Author(s):
- Yang, Yuan; Pan, Ming; Beck, Hylke; Fisher, Colby; Beighley, R. Edward; Kao, Shih-Chieh; Hong, Yang; Wood, Eric
- Abstract:
- Conventional basin-by-basin approaches to calibrate hydrologic models are limited to gauged basins and typically result in spatially discontinuous parameter fields. Moreover, the consequent low calibration density in space falls seriously behind the need from present-day applications like high resolution river hydrodynamic modeling. In this study we calibrated three key parameters of the Variable Infiltration Capacity (VIC) model at every 1/8° grid-cell using machine learning-based maps of four streamflow characteristics for the conterminous United States (CONUS), with a total of 52,663 grid-cells. This new calibration approach, as an alternative to parameter regionalization, applied to ungauged regions too. A key difference made here is that we tried to regionalize physical variables (streamflow characteristics) instead of model parameters whose behavior may often be less well understood. The resulting parameter fields no longer presented any spatial discontinuities and the patterns corresponded well with climate characteristics, such as aridity and runoff ratio. The calibrated parameters were evaluated against observed streamflow from 704/648 (calibration/validation period) small-to-medium-sized catchments used to derive the streamflow characteristics, 3941/3809 (calibration/validation period) small-to-medium-sized catchments not used to derive the streamflow characteristics) as well as five large basins. Comparisons indicated marked improvements in bias and Nash-Sutcliffe efficiency. Model performance was still poor in arid and semiarid regions, which is mostly due to both model structural and forcing deficiencies. Although the performance gain was limited by the relative small number of parameters to calibrate, the study and results here served as a proof-of-concept for a new promising approach for fine-scale hydrologic model calibrations.
- Type:
- Dataset
- Issue Date:
- 4 September 2019
155. Climate Impacts from Large Volcanic Eruptions in a High-resolution Climate Model: the Importance of Forcing Structure
- Author(s):
- Yang, Wenchang; Vecchi, Gabriel; Fueglistaler, Stephan; Horowitz, Larry; Luet, David; Muñoz, Ángel; Paynter, David; Underwood, Seth
- Abstract:
- Explosive volcanic eruptions have large climate impacts, and can serve as observable tests of the climatic response to radiative forcing. Using a high resolution climate model, we contrast the climate responses to Pinatubo, with symmetric forcing, and those to Santa Maria and Agung, which had meridionally asymmetric forcing. Although Pinatubo had larger global-mean forcing, asymmetric forcing strongly shifts the latitude of tropical rainfall features, leading to larger local precipitation/TC changes. For example, North Atlantic TC activity over is enhanced/reduced by SH-forcing (Agung)/NH-forcing (Santa Maria), but changes little in response to the Pinatubo forcing. Moreover, the transient climate sensitivity estimated from the response to Santa Maria is 20% larger than that from Pinatubo or Agung. This spread in climatic impacts of volcanoes needs to be considered when evaluating the role of volcanoes in global and regional climate, and serves to contextualize the well-observed response to Pinatubo.
- Type:
- Dataset
- Issue Date:
- 2019
156. Dust and Starlight Maps for Galaxies in the KINGFISH Sample
- Author(s):
- Aniano, G.; Draine, B.T.; Hunt, L.K.; Sandstrom, K.; Calzetti, D.; Kennicutt, R.C.; Dale, D.A.; Galametz, M.; Gordon, K.D.; Leroy, A.K.; Smith, J.-D.T.; Roussel, H.; Sauvage, M.; Walter, F.; Armus, L.; Bolatto, A.D.; Boquien, M.; Crocker, A.; De Looze, I.; Donovan Meyer, J.; Helou, G.; Hinz, J.; Johnson, B.D.; Koda, J.; Miller, A.; Montiel, E.; Murphy, E.J.; Relano, M.; Rix, H.-W.; Schinnerer, E.; Skibba, R.; Wolfire, M.G.; Engelbracht, C.W.
- Abstract:
- Dust and starlight have been modeled for the KINGFISH project galaxies. For each pixel in each galaxy, we estimate: (1) dust surface density; (2) q_PAH, the dust mass fraction in PAHs; (3) distribution of starlight intensities heating the dust; (4) luminosity emitted by the dust; and (5) dust luminosity from regions with high starlight intensity. The modeling is as described in the paper "Modeling Dust and Starlight in Galaxies Observed by Spitzer and Herschel: The KINGFISH Sample", by G. Aniano, B.T. Draine, L.K. Hunt, K. Sandstrom, D. Calzetti, R.C. Kennicutt, D.A, Dale, and 26 other authors, accepted for publication in The Astrophysical Journal.
- Type:
- Dataset and Image
157. Initial transport and turbulence analysis and gyrokinetic simulation validation in NSTX-U L-mode plasmas
- Author(s):
- Guttenfelder, W.; Kaye, S.M.; Kreite, D.M.; Bell, R.E.; Diallo, A.; LeBlanc, B.P.; McKee, G.R.; Podesta, M.; Sabbagh, S.A.; Smith, D.R.
- Abstract:
- Transport analysis, ion-scale turbulence measurements, and initial linear and nonlinear gyrokinetic simulations are reported for a transport validation study based on low aspect ratio NSTX-U L-mode discharges. The relatively long, stationary L-modes enabled by the upgraded centerstack provide a more ideal target for transport validation studies that were not available during NSTX operation. Transport analysis shows that anomalous electron transport dominates energy loss while ion thermal transport is well described by neoclassical theory. Linear gyrokinetic GYRO analysis predicts that ion temperature gradient (ITG) modes are unstable around normalized radii $\rho$=0.6-0.8, although $E\timesB$ shearing rates are larger than the linear growth rates over much of that region. Deeper in the core ($\rho$=0.4-0.6), electromagnetic microtearing modes (MTM) are unstable as a consequence of the relatively high beta and collisionality in these particular discharges. Consistent with the linear analysis, local, nonlinear ion-scale GYRO simulations predict strong ITG transport at $\rho$=0.76, whereas electromagnetic MTM transport is important at $\rho$=0.47. The prediction of ion-scale turbulence is consistent with 2D beam emission spectroscopy (BES) that measures the presence of broadband ion-scale fluctuations. Interestingly, the BES measurements also indicate the presence of bi-modal poloidal phase velocity propagation that could be indicative of two different turbulence types. However, in the region between ($\rho$=0.56, 0.66), ion-scale simulations are strongly suppressed by the locally large $E\timesB$ shear. Instead, electron temperature gradient (ETG) turbulence simulations predict substantial transport, illustrating electron-scale contributions can be important in low aspect ratio L-modes, similar to recent analysis at conventional aspect ratio. However, agreement within experimental uncertainties has not been demonstrated, which requires additional simulations to test parametric sensitivities. The potential need to include profile-variation effects (due to the relatively large value of $\rho_*$=$\rho_i$/a at low aspect ratio), including electromagnetic and possibly multi-scale effects, is also discussed.
- Type:
- Dataset
- Issue Date:
- March 2019
158. Instability of shear flows in spatially periodic domains
- Abstract:
- Force-driven parallel shear flow in a spatially periodic domain is shown to be linearly unstable with respect to both the Reynolds number and the domain aspect ratio. This finding is confirmed by computer simulations, and a simple expression is derived to determine stable flow conditions. Periodic extensions of Couette and Poiseuille flows are unstable at Reynolds numbers two orders of magnitude smaller than their aperiodic equivalents because the periodic boundaries impose fundamentally different constraints. This instability has important implications for designing computational models of nonlinear dynamic processes with periodicity.
- Type:
- Dataset
159. Light Curves from a Search for Variable Stars in the Globular Cluster M4 with K2
- Abstract:
- The data are 4554 light curves derived from images taken of the globular cluster M4 by the Kepler space telescope during the K2 portion of its mission, specifically during Campaign 2 of that mission, which occurred in 2014. A total of 3856 images were taken over approximately three months at a cadence of approximately half an hour. The purpose of these observations was to find stars and other objects that vary in brightness over time --- variable stars. Also included is a table with associated information for each of the 4554 objects and their light curves.
- Type:
- collection and Dataset
160. Methane emissions from oil and gas platforms in the North Sea.
- Author(s):
- Riddick, Stuart; Mauzerall, Denise
- Abstract:
- Since 1850 the concentration of atmospheric methane (CH4), a potent greenhouse gas, has more than doubled. Recent studies suggest that emission inventories may be missing sources and underestimating emissions. To investigate whether offshore oil and gas platforms leak CH4 during normal operation, we measured CH4 mole fractions around eight oil and gas production platforms in the North Sea which were neither flaring gas nor off-loading oil. We use the measurements from summer 2017, along with meteorological data, in a Gaussian plume model to estimate CH4 emissions from each platform. We find CH4 mole fractions of between 11 and 370 ppb above background concentrations downwind of the platforms measured, corresponding to a median CH4 emission of 6.8 g CH4 s-1 for each platform, with a range of 2.9 to 22.3 g CH4 s-1. When matched to production records, during our measurements individual platforms lost between 0.04% and 1.4% of gas produced with a median loss of 0.23%. When the measured platforms are considered collectively, (i.e. the sum of platforms’ emission fluxes weighted by the sum of the platforms’ production), we estimate the CH4 loss to be 0.19% of gas production. These estimates are substantially higher than the emissions most recently reported to the National Atmospheric Emission Inventory (NAEI) for total CH4 loss from United Kingdom platforms in the North Sea. The NAEI reports CH4 losses from the offshore oil and gas platforms we measured to be 0.13% of gas production, with most of their emissions coming from gas flaring and offshore oil loading, neither of which were taking place at the time of our measurements. All oil and gas platforms we observed were found to leak CH4 during normal operation and much of this leakage has not been included in UK emission inventories. Further research is required to accurately determine total CH4 leakage from all offshore oil and gas operations and to properly include the leakage in national and international emission inventories.
- Type:
- Dataset
- Issue Date:
- February 2019
161. Modelling of Ablatant Deposition from Electromagnetically Driven Radiative Pellets for Disruption Mitigation Studies
- Author(s):
- Lunsford, Robert; Raman, Roger; Brooks, Arthur; Ellis, Robert A.; Lay, W-S;
- Abstract:
- The Electromagnetic Particle Injector (EPI) concept is advanced through the simulation of ablatant deposition into ITER H-mode discharges with calculations showing penetration past the H-mode pedestal for a range of injection velocities and granule sizes concurrent with the requirements of disruption mitigation. As discharge stored energy increases in future fusion devices such as ITER, control and handling of disruption events becomes a critical issue. An unmitigated disruption could lead to failure of the plasma facing components resulting in financially and politically costly repairs. Methods to facilitate the quench of an unstable high current discharge are required. With the onset warning time for some ITER disruption events estimated to be less than 10 ms, a disruption mitigation system needs to be considered which operates at injection speeds greater than gaseous sound speeds. Such an actuator could then serve as a means to augment presently planned pneumatic injection systems. The EPI uses a rail gun concept whereby a radiative payload is delivered into the discharge by means of the JxB forces generated by an external current pulse, allowing for injection velocities in excess of 1 km/s. The present status of the EPI project is outlined, including the addition of boost magnetic coils. These coils augment the self-generated rail gun magnetic field and thus provide a more efficient acceleration of the payload. The coils and the holder designed to constrain them have been modelled with the ANSYS code to ensure structural integrity through the range of operational coil cu
- Type:
- Dataset
- Issue Date:
- June 2019
162. Physics design for a lithium vapor box divertor experiment on Magnum-PSI
- Author(s):
- Schwartz, Jacob; Emdee, Eric; Goldston, Robert; Jaworski, Michael
- Abstract:
- The lithium vapor box divertor is a potential solution for power exhaust in toroidal confinement devices. The divertor plasma interacts with a localized, dense cloud of lithium vapor, leading to volumetric radiation, cooling, recombination, and detachment. To minimize contamination of the core plasma, lithium vapor is condensed on cool (300°C to 400°C) baffles upstream of the detachment point. Before implementing this in a toroidal plasma device with a slot divertor geometry, we consider an experiment with a scaled baffled-pipe geometry in the high-power linear plasma device Magnum-PSI. Three 15 cm-scale open cylinders joined by 6 cm diameter ‘nozzles’ are positioned on the plasma beam axis upstream of a target. The central box may be loaded with several tens of grams of lithium, which can be evaporated at 650°C to produce a vapor predicted, using a simple plasma-neutral interaction model, to be dense enough to cause volumetric detachment in the plasma. The power delivered to the target and box walls as measured by increases in their temperatures after a 10 s plasma pulse can be compared to determine the effectiveness of the vapor in detaching the plasma. Direct Simulation Monte Carlo simulations are performed to estimate the flow rates of lithium vapor between the boxes and to estimate the trapping of H2 delivered by the plasma in the boxes, which could inadvertently lead to detachment. Details of the geometry, simulations, and possible diagnostic techniques are presented.
- Type:
- Dataset
- Issue Date:
- 30 January 2019
163. Reduced Model for Direct Induction Startup Scenario Development on MAST-U and NSTX-U
- Author(s):
- Battaglia, D.J.; Thornton, A.J.; Gerhardt, S.P.; Kirk, A.; Kogan, L; Menard, J.E.
- Abstract:
- A reduced semi-empirical model using time-dependent axisymmetric vacuum field calculations is used to develop the prefill and feed-forward coil current targets required for reliable direct induction (DI) startup on the new MA-class spherical tokamaks, MAST-U and NSTX-U. The calculations are constrained by operational limits unique to each device, such as the geometry of the conductive elements and active coils, power supply specifications and coil heating and stress limits. The calculations are also constrained by semi-empirical models for sufficient breakdown, current drive, equilibrium and stability of the plasma developed from a shared database. A large database of DI startup on NSTX and NSTX-U is leveraged to quantify the requirements for achieving a reliable breakdown (Ip ~ 20 kA). It is observed that without pre-ionization, STs access the large E/P regime at modest loop voltage (Vloop) where the electrons in the weakly ionized plasma are continually accelerating along the open field lines. This ensures a rapid (order millisecond) breakdown of the neutral gas, even without pre-ionization or high-quality field nulls. The timescale of the initial increase in Ip on NSTX is reproduced in the reduced model provided a mechanism for impeding the applied electric field is included. Most discharges that fail in the startup phase are due to an inconsistency in the evolution of the plasma current (Ip) and equilibrium field or loss of vertical stability during the burn-through phase. The requirements for the self-consistent evolution of the fields in the weakly and full-ionized plasma states are derived from demonstrated DI startup on NSTX, NSTX-U and MAST. The predictive calculations completed for MAST-U and NSTX-U illustrate that the maximum Ip ramp rate (dIp/dt) in the early startup phase is limited by the voltage limits on the poloidal field coils on MAST-U and passive vertical stability on NSTX-U.
- Type:
- Dataset
- Issue Date:
- August 2019
164. Sound velocities in shock-synthesized stishovite to 72 GPa
- Author(s):
- Berryman, Eleanor J.; Winey, J. M.; Gupta, Yogendra M.; Duffy, Thomas S.
- Abstract:
- Stishovite (rutile-type SiO2) is the archetype of dense silicates and may occur in post-garnet eclogitic rocks at lower-mantle conditions. Sound velocities in stishovite are fundamental to understanding its mechanical and thermodynamic behavior at high pressure and temperature. Here, we use plate-impact experiments combined with velocity interferometry to determine the stress, density, and longitudinal sound speed in stishovite formed during shock compression of fused silica at 44 GPa and above. The measured sound speeds range from 12.3(8) km/s at 43.8(8) GPa to 9.8(4) km/s at 72.7(11) GPa. The decrease observed at 64 GPa reacts a decrease in the shear modulus of stishovite, likely due to the onset of melting. By 72 GPa, the measured sound speed agrees with the theoretical bulk sound speed indicating loss of all shear stiffness due to complete melting. Our sound velocity results provide direct evidence for shock-induced melting, in agreement with previous pyrometry data.
- Type:
- Dataset
- Issue Date:
- 2019
165. Sowing the Seeds for More Usable Web Archives: A Usability Study of Archive-It
- Author(s):
- Abrams, Samantha; Antracoli, Alexis; Appel, Rachel; Caust-Ellenbogen, Celia; Dennison, Sarah; Duncan, Sumitra; Ramsay, Stefanie
- Abstract:
- In 2017, seven members of the Archive-It Mid-Atlantic Users Group (AITMA) conducted a study of 14 subjects representative of their stakeholder populations to assess the usability of Archive-It, a web archiving subscription service of the Internet Archive. While Archive-It is the most widely-used tool for web archiving, little is known about how users interact with the service. This study intended to teach us what users expect from web archives, which exist as another form of archival material. End-user subjects executed four search tasks using the public Archive-It interface and the Wayback Machine to access archived information on websites from the facilitators’ own harvested collections and provide feedback about their experiences. The tasks were designed to have straightforward pass or fail outcomes, and the facilitators took notes on the subjects’ behavior and commentary during the sessions. Overall, participants reported mildly positive impressions of Archive-It public user interface based on their session. The study identified several key areas of improvement for the Archive-It service pertaining to metadata options, terminology display, indexing of dates, and the site’s search box.
- Type:
- Dataset
- Issue Date:
- 2019
166. Spontaneous multi-keV electron generation in a low-RF-power axisymmetric mirror machine
- Author(s):
- Swanson, C.;Cohen, S.A.
- Abstract:
- Title: Spontaneous multi-keV electron generation in a low-RF-power axisymmetric mirror machine Abstract: X-ray emission shows the existence of multi-keV electrons in low-temperature, low-power, capacitively-coupled RF-heated magnetic-mirror plasmas that also contain a warm (300 eV) minority electron population. Though these warm electrons are initially passing particles, we suggest that collisionless scattering -- mu non-conservation in the static vacuum field -- is responsible for a minority of them to persist in the mirror cell for thousands of transits during which time a fraction are energized to a characteristic temperature of 3 keV, with some electrons reaching energies above 30 keV. A heuristic model of the heating by a Fermi-acceleration-like mechanism is presented, with mu non-conservation in the static vacuum field as an essential feature.
- Type:
- Dataset
- Issue Date:
- May 2019
167. Study of liquid metal surface wave damping in the presence of magnetic fields and electrical currents
- Author(s):
- Fisher, A.E.; Hvasta, M.G.; Kolemen, E.
- Abstract:
- Experiments and predictions of surface wave damping in liquid metal due to a surface aligned magnetic field and externally regulated j × B force are presented. Fast-flowing, liquid-metal plasma facing components (LM-PFCs) are a proposed alternative to solid PFCs that are unable to handle the high heat flux, thermal stresses, and radiation damage in a tokamak. The significant technical challenges associated with LM-PFCs compared to solid PFCs are justified by greater heat flux management, self-healing properties, and reduced particle recycling. However, undesirable engineering challenges such as evaporation and splashing of the liquid metal introduce excessive impurities into the plasma and degrade plasma performance. Evaporation may be avoided through high-speed flow that limits temperature rise of the liquid metal by reducing heat flux exposure time, but as flow speed increases the surface may become more turbulent and prone to splashing and uneven surfaces. Wave damping is one mechanism that reduces surface disturbance and thus the chances of liquid metal impurity introduction into the plasma. Experiments on the Liquid Metal eXperiment Upgrade (LMX-U) examined damping under the influence of transverse magnetic fields and vertically directed Lorentz force.
- Type:
- Dataset
- Issue Date:
- March 2019
168. TRANSP-based Optimization Towards Tokamak Scenario Development
- Author(s):
- W.P. Wehner, E. Schuster, M.D. Boyer, F. Poli
- Abstract:
- An optimization approach that incorporates the predictive transport code TRANSP is proposed for tokamak scenario development. Optimization methods are often employed to develop open-loop control strategies to aid access to high performance tokamak scenarios. In general, the optimization approaches use control-oriented models, i.e. models that are reduced in complexity and prediction accuracy as compared to physics-oriented transport codes such as TRANSP. In the presented approach, an optimization procedure using the TRANSP code to simulate the tokamak plasma is considered for improved predictive capabilities. As a test case, the neutral beam injection (NBI) power is optimized to develop a control strategy that maximizes the non-inductive current fraction during the ramp-up phase for NSTX-U. Simulation studies towards the achievement of non-inductive ramp up in NSTX-U have already been carried out with the TRANSP code. The optimization-based approach proposed in this work is used to maximize the non-inductive current fraction during ramp-up in NSTX-U, demonstrating that the scenario development task can be automated. An additional test case considers optimization of the current ramp rate in DIII-D for obtaining a stationary plasma characterized by a flat loop voltage profile in the flattop phase.
- Type:
- Dataset
- Issue Date:
- April 2019
169. TRANSP-based closed-loop simulations of current profile optimal regulation in NSTX-Upgrade
- Author(s):
- Ilhan, Z.O.; Boyer. M.D.; Schuster, E.
- Abstract:
- Active control of the toroidal current density profile is critical for the upgraded National Spherical Torus eXperiment device (NSTX-U) to maintain operation at the desired high-performance, MHD-stable, plasma regime. Initial efforts towards current density profile control have led to the development of a control-oriented, physics-based, plasma-response model, which combines the magnetic diffusion equation with empirical correlations for the kinetic profiles and the non-inductive current sources. The developed control-oriented model has been successfully tailored to the NSTX-U geometry and actuators. Moreover, a series of efforts have been made towards the design of model-based controllers, including a linear-quadratic-integral optimal control strategy that can regulate the current density profile around a prescribed target profile while rejecting disturbances. In this work, the tracking performance of the proposed current-profile optimal controller is tested in numerical simulations based on the physics-oriented code TRANSP. These high-fidelity closed-loop simulations, which are a critical step before experimental implementation and testing, are enabled by a flexible framework recently developed to perform feedback control design and simulation in TRANSP.
- Type:
- Dataset
- Issue Date:
- March 2019
170. Unsupervised identification of the internal states that shape natural behavior
- Author(s):
- Calhoun, Adam; Pillow, Jonathan; Murthy, Mala
- Type:
- Dataset
- Issue Date:
- 28 May 2019
171. Calibrationless rotating Lorentz-force flowmeters for low flow rate applications
- Author(s):
- Hvasta, M. G.; Dudt, D.; Fisher, A. E.; Kolemen, E.
- Abstract:
- A 'weighted magnetic bearing' has been developed to improve the performance of rotating Lorentz-force flowmeters (RLFFs). Experiments have shown that the new bearing reduces frictional losses within a double-sided, disc-style RLFF to negligible levels. Operating such an RLFF under 'frictionless' conditions provides two major benefits. First, the steady-state velocity of the RLFF magnets matches the average velocity of the flowing liquid at low flow rates. This enables an RLFF to make accurate volumetric flow measurements without any calibration or prior knowledge of the fluid properties. Second, due to minimized frictional losses, an RLFF is able to measure low flow rates that cannot be detected when conventional, high-friction bearings are used. This paper provides a brief background on RLFFs, gives a detailed description of weighted magnetic bearings, and compares experimental RLFF data to measurements taken with a commercially available flowmeter.
- Type:
- Dataset
- Issue Date:
- 29 May 2018
172. Collapse of reacted fracture surface decreases permeability and frictional strength
- Author(s):
- Peters, Catherine A.; Spokas, Kasparas
- Abstract:
- Geochemical and geomechanical perturbations of the subsurface caused by the injection of fluids present the risk of leakage and seismicity. This study investigated how flow of acidic fluids affects hydraulic and frictional properties of fractures using experiments with 3.8 cm-long specimens of Eagle Ford shale, a laminated shale with carbonate-rich strata. In low-pressure flow cells, one set of samples was exposed to an acidic brine and another set was exposed to a neutral brine. X-ray computed tomography and x-ray fluorescence analysis revealed that samples exposed to the acidic brine were calcite-depleted and had developed a porous altered layer, while the other set showed little evidence of alteration. After reaction, samples were compacted and sheared in a triaxial cell that supplied normal stress and differential pore pressure at prescribed sliding velocities, independently measuring friction and permeability. During the initial compaction, the porous altered layer collapsed into fine particles that filled the fracture aperture. This effectively impeded flow and sealed the fracture, resulting in a decrease in fracture permeability by 1 to 2 orders of magnitude relative to the compressed unaltered fractures. During shear, the collapsed layer of fine-grained particles prevented the formation of interlocking micro-asperities resulting in lower frictional strength. With regard to subsurface risks, this study showcases how coupled geochemical and geomechanical processes could favorably seal fractures to inhibit leakage, but also could increase the likelihood of induced seismicity. These findings have important implications for geological carbon sequestration, pressurized fluid energy storage, geothermal energy, and other subsurface technologies.
- Type:
- Dataset
- Issue Date:
- 2018
173. Demonstrating electromagnetic control of free-surface, liquid-metal flows relevant to fusion reactors
- Author(s):
- Hvasta, M. G.; Kolemen, E.; Fisher, A. E.; Ji, H.
- Abstract:
- Plasma-facing components (PFC's) made from solid materials may not be able to withstand the large heat and particle fluxes that will be produced within next-generation fusion reactors. To address the shortcomings of solid PFC's, a variety of liquid-metal (LM) PFC concepts have been proposed. Many of the suggested LM-PFC designs rely on electromagnetic restraint (Lorentz force) to keep free-surface, liquid-metal flows adhered to the interior surfaces of a fusion reactor. However, there is very little, if any, experimental data demonstrating that free-surface, LM-PFC's can actually be electromagnetically controlled. Therefore, in this study, electrical currents were injected into a free-surface liquid-metal that was flowing through a uniform magnetic field. The resultant Lorentz force generated within the liquid-metal affected the velocity and depth of the flow in a controllable manner that closely matched theoretical predictions. These results show the promise of electromagnetic control for LM-PFC's and suggest that electromagnetic control could be further developed to adjust liquid-metal nozzle output, prevent splashing within a tokamak, and alter heat transfer properties for a wide-range of liquid-metal systems.
- Type:
- Dataset
- Issue Date:
- January 2018
174. Design and measurement methods for a lithium vapor box similarity experiment
- Author(s):
- Schwartz, J. A.; Emdee, E. D.; Jaworski, M. A; Goldston, R. J.
- Abstract:
- The lithium vapor box divertor is a concept for handling the extreme divertor heat fluxes in magnetic fusion devices. In a baffled slot divertor, plasma interacts with a dense cloud of Li vapor which radiates and cools the plasma, leading to recombination and detachment. Before testing on a tokamak the concept should be validated: we plan to study detachment and heat redistribution by a Li vapor cloud in laboratory experiments. Mass changes and temperatures are measured to validate a Direct Simulation Monte Carlo model of neutral Li. The initial experiment involves a 5 cm diameter steel box containing 10g of Li held at 650 degrees C as vapor flows out a wide nozzle into a similarly-sized box at a lower temperature. Diagnosis is made challenging by the required material compatibility with lithium vapor. Vapor pressure is a steep function of temperature, so to validate mass flow models to within 10%, absolute temperature to within 4.5K is required. The apparatus is designed to be used with an analytical balance to determine mass transport. Details of the apparatus and methods of temperature and mass flow measurements are presented.
- Type:
- Dataset
- Issue Date:
- August 2018
175. Detection of an electron beam in a high density plasma via an electrostatic probe
- Author(s):
- Majeski, Stephen; Yoo, Jongsoo; Zweben, Stewart; Yamada, Masaaki
- Abstract:
- An electron beam is detected by a 1D floating potential probe array in a relatively high density (10e12 − 10e13 cm−3) and low temperature (∼ 5 eV) plasma of the Magnetic Reconnection Experiment (MRX). Clear perturbations in the floating potential profile by the electron beam are observed. Based on the floating potential profile and a current balance equation to the probe array tips, the effective width of the electron beam is determined, from which we determine the radial and toroidal beam current density profiles. After the profile of the electron beam is specified from the measured beam current, we demonstrate the consistency of the current balance equation and the location of the perturbation is also in agreement with field line mapping. No significant broadening of the electron beam is observed after the beam propagates for tens of centimeters through the high density plasma. These results prove that the field line mapping is, in principle, possible in high density plasmas.
- Type:
- Dataset
- Issue Date:
- 2018
176. ELM frequency enhancement and discharge modification through lithium granule injection into EAST H-modes
- Author(s):
- Lunsford; Hsu, J.S.; Sun, Z.; Maingi, R.; Mansfield, D.K.; Xu, W.; Zuo, G.Z.; Huang, M.; Diallo, A.; Osborne, T.; Tritz, K.; Canik, J.; Meng, X.C.; Gong, X.Z.; Wan, B.N.; Li, J.G.; EAST Team
- Abstract:
- The injection of impurity granules into fusion research discharges can serve as a catalyst for ELM events. For sufficiently low ELM frequencies, and granule sizes above a threshold, this can result in full control of the ELM cycle, referred to as ELM pacing. For this research, we extend the investigation to conditions where the natural ELM frequency is too high for ELM pacing to be realized. Utilizing multiple sizes of lithium granules and classifying their effects by granule size, we demonstrate that ELM mitigation through frequency multiplication can be used at ELM triggering rates that nominally make ELM pacing unrealizable. We find that above a size threshold, injected granules promptly trigger ELMs and commensurately enhance the ELM frequency . Below this threshold size, injection of an individual granule does not always lead to the prompt triggering of an ELM; however, collective ablation in the edge pedestal region does enhance the ELM frequency. Specifically, Li granules too small to individually trigger ELMs were injected into EAST H-mode discharges at frequencies up to 2.3 kHz; collectively the granules were observed to enhance the natural ELM frequency up to 620 Hz, resulting in a ~2.4x multiplication of the natural ELM frequency and a 50% decrease of the ELM size.
- Type:
- Dataset
- Issue Date:
- October 2018
177. Effects of Axial Boundary Conductivity on a Free Stewartson-Shercliff Layer
- Author(s):
- Caspary, Kyle J.; Choi, Dahan; Ebrahimi, Fatima; Gilson, Erik P.; Goodman, Jeremy; Ji, Hantao
- Abstract:
- The effects of axial boundary conductivity on the formation and stability of a magnetized free Stewartson-Shercliff layer (SSL) in a short Taylor-Couette device are reported. As the axial field increases with insulating endcaps, hydrodynamic Kelvin-Helmholtz-type instabilities set in at the SSLs of the conducting fluid, resulting in a much reduced flow shear. With conducting endcaps, SSLs respond to an axial field weaker by the square root of the conductivity ratio of endcaps to fluid. Flow shear continuously builds up as the axial field increases despite the local violation of the Rayleigh criterion, leading to a large number of hydrodynamically unstable modes. Numerical simulations of both the mean flow and the instabilities are in agreement with the experimental results.
- Type:
- Dataset
- Issue Date:
- 2018
178. Experimental demonstration of hydraulic jump control in liquid metal channel flow using Lorentz force
- Author(s):
- Fisher, Adam; Kolemen, Egemen; Hvasta, Mike
- Abstract:
- In this paper, hydraulic jump control using electromagnetic force in a liquid metal flow is presented. The control methods used give insight into the hydraulic jump behavior in the presence of magnetic fields and electrical currents. Flowing liquid metals is a proposed solution to heat flux challenges posed in fusion reactors, specifically the tokamak. Unfortunately, thin, fast-flowing liquid metal divertor concepts for fusion reactors are susceptible to hydraulic jumps that drastically reduce the liquid metal flow speed, leading to potential problems such as excessive evaporation, unsteady power removal, and possible plasma disruption. Highly electrically conductive flows within the magnetic fields do not exhibit traditional hydraulic jump behavior. There is very little research investigating the use of externally injected electrical currents and magnetic fields to control liquid metal hydraulic jumps. By using externally injected electrical currents and a magnetic field, a Lorentz force (also referred to as j × B force) may be generated to control the liquid metal jump behavior. In this work, a free-surface liquid metal—GaInSn eutectic or “galinstan”—flow through an electrically insulating rectangular duct was investigated. It was shown that applying a Lorentz force has a repeatable and predictable impact on the hydraulic jump, which can be used for liquid metal control within next-generation fusion reactors.
- Type:
- Dataset
- Issue Date:
- 2018
179. Fast animal pose estimation using deep neural networks
- Author(s):
- Pereira, Talmo D.; Aldarondo, Diego E.; Willmore, Lindsay; Kislin, Mikhail; Wang, Samuel S.-H.; Murthy, Mala; Shaevitz, Joshua W.
- Abstract:
- Recent work quantifying postural dynamics has attempted to define the repertoire of behaviors performed by an animal. However, a major drawback to these techniques has been their reliance on dimensionality reduction of images which destroys information about which parts of the body are used in each behavior. To address this issue, we introduce a deep learning-based method for pose estimation, LEAP (LEAP Estimates Animal Pose). LEAP automatically predicts the positions of animal body parts using a deep convolutional neural network with as little as 10 frames of labeled data for training. This framework consists of a graphical interface for interactive labeling of body parts and software for training the network and fast prediction on new data (1 hr to train, 185 Hz predictions). We validate LEAP using videos of freely behaving fruit flies (Drosophila melanogaster) and track 32 distinct points on the body to fully describe the pose of the head, body, wings, and legs with an error rate of <3% of the animal's body length. We recapitulate a number of reported findings on insect gait dynamics and show LEAP's applicability as the first step in unsupervised behavioral classification. Finally, we extend the method to more challenging imaging situations (pairs of flies moving on a mesh-like background) and movies from freely moving mice (Mus musculus) where we track the full conformation of the head, body, and limbs.
- Type:
- Dataset
- Issue Date:
- 30 May 2018
180. Marcellus Shale Unconventional Natural Gas Well Pad Emissions
- Author(s):
- Caulton, Dana; Zondlo, Mark
- Abstract:
- Please refer to the attached README.txt file for information on the datasets
- Type:
- Dataset
- Issue Date:
- October 2018
181. Measuring shared responses across subjects using intersubject correlation
- Author(s):
- Nastase, Samuel; Gazzola, Valeria; Hasson, Uri; Keysers, Christian
- Type:
- Dataset
- Issue Date:
- 1 January 2019
182. Modeling of a Laser-Induced Rydberg Spectroscopy diagnostic for Direct Measurement of the Local Electric Field in the Edge Region of NSTX/NSTX-U
- Author(s):
- Reymond, L.; Diallo, A.; Vekselman, V.
- Abstract:
- We discuss a novel diagnostic allowing direct measurements of the local electric field in the edge region in NSTX/NSTX-U. This laser based diagnostic's principle consists of depleting the naturally populated $n=3$ level to a Rydberg state --sensitive to electric fields-- that will result in a suppression of part of the $D_{\alpha}$ emission. We refer to this approach as Laser-Induced Rydberg Spectroscopy (LIRyS). It is shown that the local electric field can be measured through the Stark induced resonances observed as dips in the $D_\alpha$ emission. Using forward-modeling of simulated absorption spectra, we show precisions reaching \SI{\pm 2}{\kilo\volt\per\meter} in regions with a local electric field of \SI{15}{\kilo\volt\per\meter}.
- Type:
- Dataset
- Issue Date:
- July 2018
183. Plasma boundary shape control and real-time equilibrium reconstruction on NSTX-U
- Author(s):
- Boyer, M.; Battaglia, D.; Mueller, D.; Eidietis, N.; Erickson, K.; Ferron, J.; Gates, D.; Gerhardt, S.; Johnson, R.; Kolemen, E.; Menard, J.; Myers, C.; Sabbagh, S.; Scotti, F.; Vail, P.
- Abstract:
- The upgrade to the National Spherical Torus eXperiment (NSTX-U) included two main improvements: a larger center-stack, enabling higher toroidal field and longer pulse duration, and the addition of three new tangentially aimed neutral beam sources, which increase available heating and current drive, and allow for flexibility in shaping power, torque, current, and particle deposition profiles. To best use these new capabilities and meet the high-performance operational goals of NSTX-U, major upgrades to the NSTX-U Control System (NCS) hardware and software have been made. Several control algorithms, including those used for real-time equilibrium reconstruction and shape control, have been upgraded to improve and extend plasma control capabilities. As part of the commissioning phase of first plasma operations, the shape control system was tuned to control the boundary in both inner-wall limited and diverted discharges. It has been used to accurately track the requested evolution of the boundary (including the size of the inner gap between the plasma and central solenoid, which is a challenge for the ST configuration), X-point locations, and strike point locations, enabling repeatable discharge evolutions for scenario development and diagnostic commissioning.
- Type:
- Dataset
- Issue Date:
- March 2018
184. Quantitative imaging of carbon dimer precursor for nanomaterial synthesis in the carbon arc
- Author(s):
- Vekselman, V.; Khrabry, A.; Kaganovich, I.; Stratton, B.; Selinsky, R. S.; Raitses, Y.
- Abstract:
- Delineating the dominant processes responsible for nanomaterial synthesis in a plasma environment requires measurements of the precursor species contributing to the growth of nanostructures. We performed comprehensive measurements of spatial and temporal profiles of carbon dimers in sub-atmospheric-pressure carbon arc by laser-induced fluorescence. Measured spatial profiles of carbon dimers coincide with the growth region of carbon nanotubes (Fang et al 2016 Carbon 107 273-80) and vary depending on the arc operation mode, which is determined by the discharge current and the ablation rate of the graphite anode. The carbon dimer density profile exhibits large spatial and time variations due to motion of the arc core. A comparison of the experimental data with the 2D simulation results of self-consistent arc modeling shows a good agreement. The model predicts well the main processes determining spatial profiles of carbon dimers.
- Type:
- Dataset
- Issue Date:
- January 2018
185. Regional hydroclimatic variability due to contemporary deforestation in southern Amazonia and associated boundary layer characteristics
- Author(s):
- Khanna, Jaya; Medvigy, David; Fisch, Gilberto; Neves, Theomar Trindade de Araújo Tiburtino
- Abstract:
- Amazonian deforestation causes systematic changes in regional dry season precipitation. Some of these changes at contemporary large scales (a few hundreds of kilometers) of deforestation have been associated with a ‘dynamical mesoscale circulation’, induced by the replacement of rough forest with smooth pasture. In terms of decadal averages, this dynamical mechanism yields increased precipitation in downwind regions and decreased precipitation in upwind regions of deforested areas. Daily, seasonal, and interannual variations in this phenomenon may exist, but have not yet been identified or explained. This study uses observations and numerical simulations to develop relationships between the dynamical mechanism and the local- and continental-scale atmospheric conditions across a range of time scales. It is found that the strength of the dynamical mechanism is primarily controlled by the regional-scale thermal and dynamical conditions of the boundary layer, and not by the continental- and global-scale atmospheric state. Lifting condensation level and wind speed within the boundary layer have large and positive correlations with the strength of the dynamical mechanism. The strength of these relationships depends on time scale and is strongest over the seasonal cycle. Overall, the dynamical mechanism is found to be strongest during times when the atmosphere is relatively stable. Hence, for contemporary large scales of deforestation this phenomenon is found to be the prevalent convective triggering mechanism during the dry and parts of transition seasons (especially during the dry-to-wet transition), significantly affecting the hydroclimate during this period.
- Type:
- Dataset and Software
- Issue Date:
- 2018
186. Regulation of Harvester Ant Foraging as a Closed-Loop Excitable System
- Abstract:
- Ant colonies regulate activity in response to changing conditions without using centralized control. Harvester ant colonies forage in the desert for seeds, and their regulation of foraging manages a tradeoff between spending and obtaining water. Foragers lose water while outside in the dry air, but the colony obtains water by metabolizing the fats in the seeds they eat. Previous work shows that the rate at which an outgoing forager leaves the nest depends on its recent experience of brief antennal contact with returning foragers that carry a seed. We examine how this process can yield foraging rates that are robust to uncertainty and responsive to temperature and humidity across minutes to hour-long timescales. To explore possible mechanisms, we develop a low-dimensional analytical model with a small number of parameters that captures observed foraging behavior. The model uses excitability dynamics to represent response to interactions inside the nest and a random delay distribution to represent foraging time outside the nest. We show how feedback of outgoing foragers returning to the nest stabilizes the incoming and outgoing foraging rates to a common value determined by the ``volatility’’ of available foragers. The model exhibits a critical volatility above which there is sustained foraging at a constant rate and below which there is cessation of foraging. To explain how the foraging rates of colonies adjust to temperature and humidity, we propose a mechanism that relies on foragers modifying their volatility after they leave the nest and get exposed to the environment. Our study highlights the importance of feedback in the regulation of foraging activity and points to modulation of volatility as a key to explaining differences in foraging activity in response to conditions and across colonies. Our results present opportunities for generalization to other contexts and systems with excitability and feedback across multiple timescales.
- Type:
- collection and Dataset
187. Whistler wave generation by anisotropic tail electrons during asymmetric magnetic reconnection in space and laboratory
- Author(s):
- Yoo, Jongsoo; Jara-almonte, J.; Yerger, Evan; Wang, Shan; Qian, Tony; Le, Ari; Ji, Hantao; Yamada, Masaaki; Fox, William; Kim, Eun-Hwa; Chen, Li-Jen; Gershman, Daniel
- Abstract:
- Whistler wave generation near the magnetospheric separatrix during reconnection at the dayside magnetopause is studied with data from the Magnetospheric Multiscale (MMS) mission. The dispersion relation of the whistler mode is measured for the first time near the reconnection region in space, which shows that whistler waves propagate nearly parallel to the magnetic field line. A linear analysis indicates that the whistler waves are generated by temperature anisotropy in the electron tail population. This is caused by loss of electrons with a high velocity parallel to the magnetic field to the exhaust region. There is a positive correlation between activities of whistler waves and the lower-hybrid drift instability (LHDI) both in laboratory and space, indicating the enhanced transport by LHDI may be responsible for the loss of electrons with a high parallel velocity.
- Type:
- Dataset
- Issue Date:
- August 2018
188. A Reduced Resistive Wall Mode Kinetic Stability Model for Disruption Forecasting
- Author(s):
- Berkery, J.W.; Sabbagh, S.A.; Bell, R.E.; Gerhardt, S.P.; LeBlanc, B.P.
- Abstract:
- Kinetic modification of ideal stability theory from stabilizing resonances of mode-particle interaction has had success in explaining resistive wall mode (RWM) stability limits in tokamaks. With the goal of real-time stability forecasting, a reduced kinetic stability model has been implemented in the new Disruption Event Characterization and Forecasting (DECAF) code, which has been written to analyze disruptions in tokamaks. The reduced model incorporates parameterized models for ideal limits on beta, a ratio of plasma pressure to magnetic pressure, which are shown to be in good agreement with DCON code calculations. Increased beta between these ideal limits causes a shift in the unstable region of delta W_K space, where delta W_K is the change in potential energy due to kinetic effects that is solved for by the reduced model, such that it is possible for plasmas to be unstable at intermediate beta but stable at higher beta. Gaussian functions for delta W_K are defined as functions of E cross B frequency and collisionality, with parameters reflecting the experience of the National Spherical Torus Experiment (NSTX). The reduced model was tested on a database of discharges from NSTX and experimentally stable and unstable discharges were separated noticeably on a stability map in E cross B frequency, collisionality space. The reduced model only failed to predict an unstable RWM in 15.6% of cases with an experimentally unstable RWM and performed well on predicting stability for experimentally stable discharges as well.
- Type:
- Dataset
- Issue Date:
- May 2017
189. Advances in boronization on NSTX-Upgrade
- Author(s):
- Skinner, C.H.; Bedoya, F.; Scotti, F.; Allain, J.P.; Blanchard, W.; Cai, D.; Jaworski, M.; Koel, B.E.
- Abstract:
- Boronization has been effective in reducing plasma impurities and enabling access to higher density, higher confinement plasmas in many magnetic fusion devices. The National Spherical Torus eXperiment, NSTX, has recently undergone a major upgrade to NSTX-U in order to develop the physics basis for a ST-based Fusion Nuclear Science Facility (FNSF) with capability for double the toroidal field, plasma current, and NBI heating power and increased pulse duration from 1–1.5 s to 5–8 s. A new deuterated tri-methyl boron conditioning system was implemented together with a novel surface analysis diagnostic. We report on the spatial distribution of the boron deposition versus discharge pressure, gas injection and electrode location. The oxygen concentration of the plasma facing surface was measured by in-vacuo XPS and increased both with plasma exposure and with exposure to trace residual gases. This increase correlated with the rise of oxygen emission from the plasma.
- Type:
- Dataset
- Issue Date:
- January 2017
190. Amplification of local changes along the timescale processing hierarchy
- Author(s):
- Yeshurun, Yaara; Nguyen, Mai; Hasson, Uri
- Abstract:
- Small changes in word choice can lead to dramatically different interpretations of narratives. How does the brain accumulate and integrate such local changes to construct unique neural representations for different stories? In this study we created two distinct narratives by changing only a few words in each sentence (e.g. “he” to “she” or “sobbing” to “laughing”) while preserving the grammatical structure across stories. We then measured changes in neural responses between the two stories. We found that the differences in neural responses between the two stories gradually increased along the hierarchy of processing timescales. For areas with short integration windows, such as early auditory cortex, the differences in neural responses between the two stories were relatively small. In contrast, in areas with the longest integration windows at the top of the hierarchy, such as the precuneus, temporal parietal junction, and medial frontal cortices, there were large differences in neural responses between stories. Furthermore, this gradual increase in neural difference between the stories was highly correlated with an area’s ability to integrate information over time. Amplification of neural differences did not occur when changes in words did not alter the interpretation of the story (e.g. “sobbing” to “crying”). Our results demonstrate how subtle differences in words are gradually accumulated and amplified along the cortical hierarchy as the brain constructs a narrative over time.
- Type:
- Dataset
- Issue Date:
- August 2017
191. Application of IR imaging for free-surface velocity measurement in liquid-metal systems
- Author(s):
- Hvasta, M. G.; Kolemen, E.; Fisher, A.
- Abstract:
- Measuring free-surface, liquid-metal flow velocity is challenging to do in a reliable and accurate manner. This paper presents a non-invasive, easily-calibrated method of measuring the surface velocities of open-channel liquid-metal flows using an IR camera. Unlike other spatially-limited methods, this IR camera particle tracking technique provides full field-of-view data that can be used to better understand open-channel flows and determine surface boundary conditions. This method could be implemented and automated for a wide range of liquid-metal experiments, even if they operate at high-temperatures or within strong magnetic fields.
- Type:
- Dataset
- Issue Date:
- January 2017
192. Data for Nature Climate Change article 'Regional dry-season climate changes due to three decades of Amazonian deforestation'
- Author(s):
- Khanna, Jaya; Medvigy, David; Fueglistaler, Stephan; Walko, Robert
- Abstract:
- More than 20% Amazon rainforest has been cleared in the past three decades triggering important hydroclimatic changes. Small-scale (~few kilometers) deforestation in the 1980s has caused thermally-triggered atmospheric circulations that increase regional cloudiness and precipitation frequency. However, these circulations are predicted to diminish as deforestation increases. Here we use multi-decadal satellite records and numerical model simulations to show a regime shift in the regional hydroclimate accompanying increasing deforestation in Rondônia, Brazil. Compared to the 1980s, present-day deforested areas in downwind western Rondônia are found to be wetter than upwind eastern deforested areas during the local dry season. The resultant precipitation change in the two regions is approximately ±25% of the deforested area mean. Meso-resolution simulations robustly reproduce this transition when forced with increasing deforestation alone, showing a negligible role of large-scale climate variability. Furthermore, deforestation-induced surface roughness reduction is found to play an essential role in the present-day dry season hydroclimate. Our study illustrates the strong scale-sensitivity of the climatic response to Amazonian deforestation and suggests that deforestation is sufficiently advanced to have caused a shift from a thermally- to a dynamically-driven hydroclimatic regime.
- Type:
- Dataset and Software
- Issue Date:
- 2017
193. Design of Faraday cup ion detectors built by thin film deposition
- Author(s):
- Szalkowski, G.A.; Darrow, D.S.; Cecil, F.E.
- Abstract:
- Thin film Faraday cup detectors can provide measurements of fast ion loss from magnetically confined fusion plasmas. These multilayer detectors can resolve the energy distribution of the lost ions in addition to giving the total loss rate. Prior detectors were assembled from discrete foils and insulating sheets. Outlined here is a design methodology for creating detectors using thin film deposition that are suited to particular scientific goals. The intention is to use detectors created by this method on JET and NSTX-U. The detectors will consist of alternating layers of aluminum and silicon dioxide, with layer thicknesses chosen to isolate energies of interest. Thin film deposition offers the advantage of relatively simple and more mechanically robust construction compared to other methods, as well as allowing precise control of film thickness. Furthermore, this depositional fabrication technique places the layers in intimate thermal contact, providing for three-dimensional conduction and dissipation of the ion-produced heating in the layers, rather than the essentially two-dimensional heat conduction in the discrete foil stack implementation.
- Type:
- Dataset
- Issue Date:
- January 2017
194. Electron heating and energy inventory during asymmetric reconnection in a laboratory plasma
- Author(s):
- Yoo, Jongsoo; Na, Byungkeun; Jara-Almonte, Jonathan; Yamada, Maasaki; Ji, Hantao; Roytershteyn, V.; Argall, M. R.; Fox, W.; Chen, Li-Jen
- Abstract:
- Electron heating and the energy inventory during asymmetric reconnection are studied in the laboratory plasma with a density ratio of about 8 across the current sheet. Features of asymmetric reconnection such as the large density gradients near the low-density-side separatrices, asymmetric in-plane electric field, and bipolar out-of-plane magnetic field are observed. Unlike the symmetric case, electrons are also heated near the low-density-side separatrices. The measured parallel electric field may explain the observed electron heating. Although large fluctuations driven by lower-hybrid drift instabilities are also observed near the low-density-side separatrices, laboratory measurements and numerical simulations reported here suggest that they do not play a major role in electron energization. The average electron temperature increase in the exhaust region is proportional to the incoming magnetic energy per an electron/ion pair but exceeds scalings of the previous space observations. This discrepancy is explained by differences in the boundary condition and system size. The profile of electron energy gain from the electric field shows that there is additional electron energy gain associated with the electron diamagnetic current besides a large energy gain near the X-line. This additional energy gain increases electron enthalpy, not the electron temperature. Finally, a quantitative analysis of the energy inventory during asymmetric reconnection is conducted. Unlike the symmetric case where the ion energy gain is about twice more than the electron energy gain, electrons and ions obtain a similar amount of energy during asymmetric reconnection.
- Type:
- Dataset
- Issue Date:
- August 2017
195. Experimental calibration procedures for rotating Lorentz-force flowmeters
- Author(s):
- Hvasta, M. G.; Slighton, N. T.; Kolemen, E.; Fisher, A. E.
- Abstract:
- Rotating Lorentz-force flowmeters are a novel and useful technology with a range of applications in a variety of different industries. However, calibrating these flowmeters can be challenging, time-consuming, and expensive. In this paper, simple calibration procedures for rotating Lorentz-force flowmeters are presented. These procedures eliminate the need for expensive equipment, numerical modeling, redundant flowmeters, and system down-time. The calibration processes are explained in a step-by-step manner and compared to experimental results.
- Type:
- Dataset
- Issue Date:
- 2017
196. Feedback control design for non-inductively sustained scenarios in NSTX-U using TRANSP
- Author(s):
- Boyer, M.D.; Andre, R.G.; Gates, D.A.; Gerhardt, S.P.; Menard, J.E.; Poli, F.M.
- Abstract:
- This paper examines a method for real-time control of non-inductively sustained scenarios in NSTX-U by using TRANSP, a time-dependent integrated modeling code for prediction and interpretive analysis of tokamak experimental data, as a simulator. The actuators considered for control in this work are the six neutral beam sources and the plasma boundary shape. To understand the response of the plasma current, stored energy, and central safety factor to these actuators and to enable systematic design of control algorithms, simulations were run in which the actuators were modulated and a linearized dynamic response model was generated. A multi-variable model-based control scheme that accounts for the coupling and slow dynamics of the system while mitigating the effect of actuator limitations was designed and simulated. Simulations show that modest changes in the outer gap and heating power can improve the response time of the system, reject perturbations, and track target values of the controlled values.
- Type:
- Dataset
- Issue Date:
- June 2017
197. Fracture aperture maps used to study reactive transport, channelization, and permeability evolution in carbonate rocks.
- Author(s):
- Peters, Catherine
- Abstract:
- Fractures in geological formations may enable migration of environmentally relevant fluids, as in leakage of CO2 through caprocks in geologic carbon sequestration. We investigated geochemically induced alterations of fracture geometry in Indiana Limestone specimens. Experiments were the first of their kind, with periodic high-resolution imaging using X-ray computed tomography (xCT) scanning while maintaining high pore pressure (100 bar). We studied two CO2-acidified brines having the same pH (3.3) and comparable thermodynamic disequilibrium but different equilibrated pressures of CO2 (PCO2 values of 12 and 77 bar). High-PCO2 brine has a faster calcite dissolution kinetic rate because of the accelerating effect of carbonic acid. Contrary to expectations, dissolution extents were comparable in the two experiments. However, progressive xCT images revealed extensive channelization for high PCO2, explained by strong positive feedback between ongoing flow and reaction. The pronounced channel increasingly directed flow to a small region of the fracture, which explains why the overall dissolution was lower than expected. Despite this, flow simulations revealed large increases in permeability in the high-PCO2 experiment. This study shows that the permeability evolution of dissolving fractures will be larger for faster-reacting fluids. The overall mechanism is not because more rock dissolves, as would be commonly assumed, but because of accelerated fracture channelization.
- Type:
- Dataset
- Issue Date:
- December 2017
198. Full-wave simulations of ICRF heating regimes in toroidal plasmas with non-Maxwellian distribution functions
- Author(s):
- Bertelli, N; Valeo, E.J.; Green, D.L.; Gorelenkova, M.; Phillips, C.K.; Podesta, M.; Lee, J.P.; Wright, J.C.; Jaeger, E.
- Abstract:
- At the power levels required for significant heating and current drive in magnetically-confined toroidal plasma, modification of the particle distribution function from a Maxwellian shape is likely [T. H. Stix, Nucl. Fusion, 15 737 (1975)], with consequent changes in wave propagation and in the location and amount of absorption. In order to study these effects computationally, both the finite-Larmor-radius and the high-harmonic fast wave (HHFW), versions of the full-wave, hot-plasma toroidal simulation code TORIC [M. Brambilla, Plasma Phys. Control. Fusion 41, 1 (1999) and M. Brambilla, Plasma Phys. Control. Fusion 44, 2423 (2002)], have been extended to allow the prescription of arbitrary velocity distributions of the form f(v||, v_perp, psi , theta). For hydrogen (H) minority heating of a deuterium (D) plasma with anisotropic Maxwellian H distributions, the fractional H absorption varies significantly with changes in parallel temperature but is essentially independent of perpendicular temperature. On the other hand, for HHFW regime with anisotropic Maxwellian fast ion distribution, the fractional beam ion absorption varies mainly with changes in the perpendicular temperature. The evaluation of the wave-field and power absorption, through the full wave solver, with the ion distribution function provided by either aMonte-Carlo particle and Fokker-Planck codes is also examined for Alcator C-Mod and NSTX plasmas. Non-Maxwellian effects generally tends to increase the absorption with respect to the equivalent Maxwellian distribution.
- Type:
- Dataset
- Issue Date:
- May 2017
199. Injected mass deposition thresholds for lithium granule instigated triggering of edge localized modes on EAST
- Author(s):
- Lunsford, R.; Sun, Z.; Maingi, R.; Hu, J.S.; Mansfield, D.; Xu, W.; Zuo, G.Z.; Diallo, A.; Osborne, T.; Tritz, K.; Canik, J.; Huang, M.; Meng, X.C.; Gong, X.Z.; Wan, B.N.; Li, J.G.
- Abstract:
- The ability of an injected lithium granule to promptly trigger an edge localized mode (ELM) has been established in multiple experiments. By horizontally injecting granules ranging in diameter from 200 microns to 1mm in diameter into the low field side of EAST H-mode discharges we have determined that granules with diameter > 600 microns are successful in triggering ELMs more than 95% of the time. It was also demonstrated that below 600 microns the triggering efficiency decreased roughly with granule size. Granules were radially injected from the outer midplane with velocities ~ 80 m/s into EAST upper single null discharges with an ITER like tungsten monoblock divertor. These granules were individually tracked throughout their injection cycle in order to determine their efficacy at triggering an ELM. For those granules of sufficient size, ELM triggering was a prompt response to granule injection. By simulating the granule injection with an experimentally benchmarked neutral gas shielding (NGS) model, the ablatant mass deposition required to promptly trigger an ELM is calculated and the fractional mass deposition is determined.
- Type:
- Dataset
- Issue Date:
- December 2017
200. M3D-C1 simulations of the plasma response to RMPs in NSTX-U single-null and snowflake divertor configurations
- Author(s):
- Canal, G.P.; Ferraro, N.M.; Evans, T.E.; Osborne, T.H.; Menard, J.E.; Ahn, J.-W.; Maingi, R.; Wingen, A.; Ciro, D.; Frerichs, H.; Schmitz, O.; Soukhanovskii, V.; Waters, I.
- Abstract:
- Non-axisymmetric control coils and the so-called snowflake divertor configuration are two potential solutions proposed to solve two separate outstanding issues on the path towards self-sustained burning plasma operations, namely the transient energy bursts caused by edge localized modes and the steady state heat exhaust problem. In a reactor, these two proposed solutions would have to operate simultaneously and it is, therefore, important to investigate their compatibility and to identify possible conflicts that could prevent them from operating simultaneously. In this work, single- and two-fluid resistive magnetohydrodynamic calculations are used to investigate the effect of externally applied magnetic perturbations on the snowflake divertor configuration. The calculations are based on simulated NSTX-U plasmas and the results show that additional and longer magnetic lobes are created in the null-point region of the snowflake configuration, compared to those in the conventional single-null. The intersection of these longer and additional lobes with the divertor plates are expected to cause more striations in the particle and heat flux target profiles. In addition, the results indicate that the size of the magnetic lobes, in both single-null and snowflake configurations, are more sensitive to resonant magnetic perturbations than to non-resonant magnetic perturbations. The results also suggest that lower values of current in non-axisymmetric control coils would be required to suppress edge localized modes in plasmas with the snowflake configuration.
- Type:
- Dataset
- Issue Date:
- July 2017