Search

Start Over Type Dataset

202. Modeling of a Laser-Induced Rydberg Spectroscopy diagnostic for Direct Measurement of the Local Electric Field in the Edge Region of NSTX/NSTX-U

Author(s):
Reymond, L.; Diallo, A.; Vekselman, V.
Abstract:
We discuss a novel diagnostic allowing direct measurements of the local electric field in the edge region in NSTX/NSTX-U. This laser based diagnostic's principle consists of depleting the naturally populated $n=3$ level to a Rydberg state --sensitive to electric fields-- that will result in a suppression of part of the $D_{\alpha}$ emission. We refer to this approach as Laser-Induced Rydberg Spectroscopy (LIRyS). It is shown that the local electric field can be measured through the Stark induced resonances observed as dips in the $D_\alpha$ emission. Using forward-modeling of simulated absorption spectra, we show precisions reaching \SI{\pm 2}{\kilo\volt\per\meter} in regions with a local electric field of \SI{15}{\kilo\volt\per\meter}.
Type:
Dataset
Issue Date:
July 2018

205. Dynamics of filaments during the edge-localized mode crash on NSTX

Author(s):
Lampert,Mate; Diallo,Ahmed; Myra,James R.; Zweben, Stewart J.
Abstract:
Edge localized modes (ELMs) are routinely observed in H-mode plasma regimes of the National Spherical Torus Experiment (NSTX). Due to the explosive nature of the instability, only diagnostics with high temporal and spatial resolution could provide a detailed insight into the dynamics associated with the ELMs. Gas-puff imaging (GPI) at NSTX provides 2D measurements of the magnetic field aligned fluctuations (e.g. ELM filaments) in the scrape-off layer and the at the plasma edge with 2.5 us temporal and 10 mm optical resolution.A novel analysis technique was developed to estimate the frame-by-frame velocities and the spatial parameters of the dominant structures associated with the ELMs. The analysis was applied to single ELM events to characterize the ELM crash dynamics, and then extended to a database of 169 ELM events.Statistical analysis was performed in order to find the characterizing dynamics of the ELM crash. The results show that on average an ELM crash consists of a filament with a circular cross-section which is propelled outwards with a characterizing peak radial velocity of ~3.3 km/s. The radial velocity was found to be linearly dependent on the distance of the filament from the separatrix, which has never been seen before. The ELM filament is characterized by propagation in the ion-diamagnetic direction poloidally with a peak velocity of 11.4 km/s. The ELM crash lasts for approximately 100us until the radial propulsion settles back to the pre-ELM level. The experimental findings were compared with analytical theory. Two possible mechanisms were identified for explaining the observations: the curvature interchange model and the current-filament interaction model.
Type:
Dataset
Issue Date:
January 2021

216. A software package for plasma facing component analysis and design: the Heat flux Engineering Analysis Toolkit (HEAT)

Author(s):
Looby, Tom; Reinke, Matthew; Wingen, Andreas; Menard, Jonathan; Gerhardt, Stefan; Gray, Travis; Donovan, David; Unterberg, Ezekial; Klabacha, Jonathan; Messineo, Mike
Abstract:
The engineering limits of plasma facing components (PFCs) constrain the allowable operational space of tokamaks. Poorly managed heat fluxes that push the PFCs beyond their limits not only degrade core plasma performance via elevated impurities, but can also result in PFC failure due to thermal stresses or melting. Simple axisymmetric assumptions fail to capture the complex interaction between 3D PFC geometry and 2D or 3D plasmas. This results in fusion systems that must either operate with increased risk or reduce PFC loads, potentially through lower core plasma performance, to maintain a nominal safety factor. High precision 3D heat flux predictions are necessary to accurately ascertain the state of a PFC given the evolution of the magnetic equilibrium. A new code, the Heat flux Engineering Analysis Toolkit (HEAT), has been developed to provide high precision 3D predictions and analysis for PFCs. HEAT couples many otherwise disparate computational tools together into a single open source python package. Magnetic equilibrium, engineering CAD, finite volume solvers, scrape off layer plasma physics, visualization, high performace computing, and more, are connected in a single web-based user interface. Linux users may use HEAT without any software prerequisites via an appImage. This manuscript introduces HEAT, discusses the software architecture, presents first HEAT results, and outlines physics modules in development.
Type:
Dataset
Issue Date:
March 2021

217. The Dielectric Function of "Astrodust", and Absorption and Scattering Cross Sections for Spheroids

Author(s):
Draine, Bruce T.; Hensley, Brandon S.
Abstract:
The dielectric function for "Astrodust" grain material is provided for different assumed values of the dust grain shape (spheroid axis ratio) and porosity (vacuum fraction), and fraction of the interstellar iron present as metallic inclusions. For each case, the dielectric function is obtained by requiring that the grains reproduce the observed infrared opacity, and match to a physically reasonable dielectric function at 1 micron, and extending to X-ray energies. The derived dielectric functions satisfy the Kramers-Kronig relations. Dielectric functions are provided from 1 Angstrom to 5 cm (12.4 keV to 2.59e-5 eV). For each dielectric function, we also calculate absorption and scattering corss sections for spheroidal grains, for three orientations of the grain relative to incident linearly-polarized light, for wavelengths from the Lyman limit (0.0912 micron) to the microwave (4 cm), and grain "effective radii" a_eff from 3.162A to 5.012 micron.
Type:
Dataset
Issue Date:
2021

218. Telomere Length in Preterm Infants

Author(s):
Notterman, Daniel A; Schneper, Lisa M; Drake, Amanda; Piyasena, Chinthika
Abstract:
This entry contains the data used in the PLOS ONE publication entitled, "Characteristics of salivary telomere length shortening in preterm infants" by Schneper et al. The objective of the study was to examine the association between gestational age, telomere length (TL) and rate of shortening in newborns. Genomic DNA was isolated from buccal samples of 39 term infants at birth and one year and 32 preterm infants at birth, term-adjusted age (40 weeks post-conception) and age one-year corrected for gestational duration. Telomere length was measured by quantitative real-time PCR. Demographic and clinical data were collected during clinic or research visits and from hospital records. Socioeconomic status was estimated using the deprivation category (DEPCAT) scores derived from the Carstairs score of the subject's postal code.
Type:
Dataset
Issue Date:
5 January 2023

220. Machine Learning Characterization of Alfvénic and Sub-Alfvénic Chirping and Correlation With Fast-Ion Loss at NSTX

Author(s):
Woods, B. J. Q.; Duarte, V. N.; Fredrickson, E. D.; Gorelenkov, N. N.; Podestà, M.; Vann, R. G. L.
Abstract:
Abrupt large events in the Alfvenic and sub-Alfvenic frequency bands in tokamaks are typically correlated with increased fast-ion loss. Here, machine learning is used to speed up the laborious process of characterizing the behavior of magnetic perturbations from corresponding frequency spectrograms that are typically identified by humans. The analysis allows for comparison between different mode character (such as quiescent, fixed frequency, and chirping, avalanching) and plasma parameters obtained from the TRANSP code, such as the ratio of the neutral beam injection (NBI) velocity and the Alfven velocity (v_inj./v_A), the q-profile, and the ratio of the neutral beam beta and the total plasma beta (beta_beam,i / beta). In agreement with the previous work by Fredrickson et al., we find a correlation between beta_beam,i and mode character. In addition, previously unknown correlations are found between moments of the spectrograms and mode character. Character transition from quiescent to nonquiescent behavior for magnetic fluctuations in the 50200-kHz frequency band is observed along the boundary v_phi ~ (1/4)(v_inj. - 3v_A), where v_phi is the rotation velocity.
Type:
Dataset
Issue Date:
December 2019

222. Calibrationless rotating Lorentz-force flowmeters for low flow rate applications

Author(s):
Hvasta, M. G.; Dudt, D.; Fisher, A. E.; Kolemen, E.
Abstract:
A 'weighted magnetic bearing' has been developed to improve the performance of rotating Lorentz-force flowmeters (RLFFs). Experiments have shown that the new bearing reduces frictional losses within a double-sided, disc-style RLFF to negligible levels. Operating such an RLFF under 'frictionless' conditions provides two major benefits. First, the steady-state velocity of the RLFF magnets matches the average velocity of the flowing liquid at low flow rates. This enables an RLFF to make accurate volumetric flow measurements without any calibration or prior knowledge of the fluid properties. Second, due to minimized frictional losses, an RLFF is able to measure low flow rates that cannot be detected when conventional, high-friction bearings are used. This paper provides a brief background on RLFFs, gives a detailed description of weighted magnetic bearings, and compares experimental RLFF data to measurements taken with a commercially available flowmeter.
Type:
Dataset
Issue Date:
29 May 2018

223. Data for: 'How is sea level change encoded in carbonate stratigraphy?'

Author(s):
Geyman, Emily C.; Maloof, Adam C.; Dyer, Blake
Abstract:
The history of organismal evolution, seawater chemistry, and paleoclimate is recorded in layers of carbonate sedimentary rock. Meter-scale cyclic stacking patterns in these carbonates often are interpreted as representing sea level change. A reliable sedimentary proxy for eustasy would be profoundly useful for reconstructing paleoclimate, since sea level responds to changes in temperature and ice volume. However, the translation from water depth to carbonate layering has proven difficult, with recent surveys of modern shallow water platforms revealing little correlation between carbonate facies (i.e., grain size, sedimentary bed forms, ecology) and water depth. We train a convolutional neural network with satellite imagery and new field observations from a 3,000 km2 region northwest of Andros Island (Bahamas) to generate a facies map with 5 m resolution. Leveraging a newly-published bathymetry for the same region, we test the hypothesis that one can extract a signal of water depth change, not simply from individual facies, but from sequences of facies transitions analogous to vertically stacked carbonate strata. Our Hidden Markov Model (HMM) can distinguish relative sea level fall from random variability with ∼90% accuracy. Finally, since shallowing-upward patterns can result from local (autogenic) processes in addition to forced mechanisms such as eustasy, we search for statistical tools to diagnose the presence or absence of external forcings on relative sea level. With a new data-driven forward model that simulates how modern facies mosaics evolve to stack strata, we show how different sea level forcings generate characteristic patterns of cycle thicknesses in shallow carbonates, providing a new tool for quantitative reconstruction of ancient sea level conditions from the geologic record.
Type:
Dataset
Issue Date:
1 February 2021

227. Design and measurement methods for a lithium vapor box similarity experiment

Author(s):
Schwartz, J. A.; Emdee, E. D.; Jaworski, M. A; Goldston, R. J.
Abstract:
The lithium vapor box divertor is a concept for handling the extreme divertor heat fluxes in magnetic fusion devices. In a baffled slot divertor, plasma interacts with a dense cloud of Li vapor which radiates and cools the plasma, leading to recombination and detachment. Before testing on a tokamak the concept should be validated: we plan to study detachment and heat redistribution by a Li vapor cloud in laboratory experiments. Mass changes and temperatures are measured to validate a Direct Simulation Monte Carlo model of neutral Li. The initial experiment involves a 5 cm diameter steel box containing 10g of Li held at 650 degrees C as vapor flows out a wide nozzle into a similarly-sized box at a lower temperature. Diagnosis is made challenging by the required material compatibility with lithium vapor. Vapor pressure is a steep function of temperature, so to validate mass flow models to within 10%, absolute temperature to within 4.5K is required. The apparatus is designed to be used with an analytical balance to determine mass transport. Details of the apparatus and methods of temperature and mass flow measurements are presented.
Type:
Dataset
Issue Date:
August 2018

229. Physics design for a lithium vapor box divertor experiment on Magnum-PSI

Author(s):
Schwartz, Jacob; Emdee, Eric; Goldston, Robert; Jaworski, Michael
Abstract:
The lithium vapor box divertor is a potential solution for power exhaust in toroidal confinement devices. The divertor plasma interacts with a localized, dense cloud of lithium vapor, leading to volumetric radiation, cooling, recombination, and detachment. To minimize contamination of the core plasma, lithium vapor is condensed on cool (300°C to 400°C) baffles upstream of the detachment point. Before implementing this in a toroidal plasma device with a slot divertor geometry, we consider an experiment with a scaled baffled-pipe geometry in the high-power linear plasma device Magnum-PSI. Three 15 cm-scale open cylinders joined by 6 cm diameter ‘nozzles’ are positioned on the plasma beam axis upstream of a target. The central box may be loaded with several tens of grams of lithium, which can be evaporated at 650°C to produce a vapor predicted, using a simple plasma-neutral interaction model, to be dense enough to cause volumetric detachment in the plasma. The power delivered to the target and box walls as measured by increases in their temperatures after a 10 s plasma pulse can be compared to determine the effectiveness of the vapor in detaching the plasma. Direct Simulation Monte Carlo simulations are performed to estimate the flow rates of lithium vapor between the boxes and to estimate the trapping of H2 delivered by the plasma in the boxes, which could inadvertently lead to detachment. Details of the geometry, simulations, and possible diagnostic techniques are presented.
Type:
Dataset
Issue Date:
30 January 2019

230. Delivery Gig Worker Interviews on Automation at Work

Author(s):
Enriquez, Diana
Abstract:
These data include 39 structured interview transcripts. Each case is someone who worked at the time for Uber, UberEats, Lyft, and/or Amazon Flex (Amazon’s contractor delivery service). These data were collected between July and September 2019. All but one of the interviews occurred over the phone. My questions are focused on the structure of their gig work jobs and the technology they used at work or expected to use at work in the future. I included a description of the data, the recruitment methods, and the discussion guide in this ReadMe file. 
Type:
Dataset
Issue Date:
21 September 2021

231. A scalable real-time framework for Thomson scattering analysis: Application to NSTX-U

Author(s):
F. M. Laggner, A. Diallo, B. P. LeBlanc, R. Rozenblat, G. Tchilinguirian, E.Kolemen, the NSTX-U team
Abstract:
A detailed description of a prototype setup for real-time (rt) Thomson scattering (TS) analysis is presented and implemented in the multi-point Thomson scattering (MPTS) diagnostic system at the National Spherical Torus Experiment Upgrade(NSTX-U). The data acquisition hardware was upgraded with rt capable electronics (rt-analog digital converters (ADCs) and a rt server) that allow for fast digitization of the laser pulse signal of eight radial MPTS channels. In addition, a new TS spectrum analysis software for a rapid calculation of electron temperature (Te) and electron density (ne) was developed. Testing of the rt hardware and data analysis soft-ware was successfully completed and benchmarked against the standard, post-shot evaluation. Timing tests were performed showing that the end-to-end processing time was reproducibly below 17 ms for the duration of at least 5 s, meeting a 60 Hz deadline by the laser pulse repetition rate over the length of a NSTX-U discharge. The presented rt framework is designed to be scalable in system size, i.e. incorporation of additional radial channels by solely adding additional rt capable hardware. Furthermore, it is scalable in its operation duration and was continuously run for up to 30 min, making it an attractive solution for machines with long discharge duration such as advanced, non-inductive tokamaks or stellarators.
Type:
Dataset
Issue Date:
March 2019

232. Regional hydroclimatic variability due to contemporary deforestation in southern Amazonia and associated boundary layer characteristics

Author(s):
Khanna, Jaya; Medvigy, David; Fisch, Gilberto; Neves, Theomar Trindade de Araújo Tiburtino
Abstract:
Amazonian deforestation causes systematic changes in regional dry season precipitation. Some of these changes at contemporary large scales (a few hundreds of kilometers) of deforestation have been associated with a ‘dynamical mesoscale circulation’, induced by the replacement of rough forest with smooth pasture. In terms of decadal averages, this dynamical mechanism yields increased precipitation in downwind regions and decreased precipitation in upwind regions of deforested areas. Daily, seasonal, and interannual variations in this phenomenon may exist, but have not yet been identified or explained. This study uses observations and numerical simulations to develop relationships between the dynamical mechanism and the local- and continental-scale atmospheric conditions across a range of time scales. It is found that the strength of the dynamical mechanism is primarily controlled by the regional-scale thermal and dynamical conditions of the boundary layer, and not by the continental- and global-scale atmospheric state. Lifting condensation level and wind speed within the boundary layer have large and positive correlations with the strength of the dynamical mechanism. The strength of these relationships depends on time scale and is strongest over the seasonal cycle. Overall, the dynamical mechanism is found to be strongest during times when the atmosphere is relatively stable. Hence, for contemporary large scales of deforestation this phenomenon is found to be the prevalent convective triggering mechanism during the dry and parts of transition seasons (especially during the dry-to-wet transition), significantly affecting the hydroclimate during this period.
Type:
Dataset and Software
Issue Date:
2018

234. Application of IR imaging for free-surface velocity measurement in liquid-metal systems

Author(s):
Hvasta, M. G.; Kolemen, E.; Fisher, A.
Abstract:
Measuring free-surface, liquid-metal flow velocity is challenging to do in a reliable and accurate manner. This paper presents a non-invasive, easily-calibrated method of measuring the surface velocities of open-channel liquid-metal flows using an IR camera. Unlike other spatially-limited methods, this IR camera particle tracking technique provides full field-of-view data that can be used to better understand open-channel flows and determine surface boundary conditions. This method could be implemented and automated for a wide range of liquid-metal experiments, even if they operate at high-temperatures or within strong magnetic fields.
Type:
Dataset
Issue Date:
January 2017

235. Demonstrating electromagnetic control of free-surface, liquid-metal flows relevant to fusion reactors

Author(s):
Hvasta, M. G.; Kolemen, E.; Fisher, A. E.; Ji, H.
Abstract:
Plasma-facing components (PFC's) made from solid materials may not be able to withstand the large heat and particle fluxes that will be produced within next-generation fusion reactors. To address the shortcomings of solid PFC's, a variety of liquid-metal (LM) PFC concepts have been proposed. Many of the suggested LM-PFC designs rely on electromagnetic restraint (Lorentz force) to keep free-surface, liquid-metal flows adhered to the interior surfaces of a fusion reactor. However, there is very little, if any, experimental data demonstrating that free-surface, LM-PFC's can actually be electromagnetically controlled. Therefore, in this study, electrical currents were injected into a free-surface liquid-metal that was flowing through a uniform magnetic field. The resultant Lorentz force generated within the liquid-metal affected the velocity and depth of the flow in a controllable manner that closely matched theoretical predictions. These results show the promise of electromagnetic control for LM-PFC's and suggest that electromagnetic control could be further developed to adjust liquid-metal nozzle output, prevent splashing within a tokamak, and alter heat transfer properties for a wide-range of liquid-metal systems.
Type:
Dataset
Issue Date:
January 2018

236. Experimental calibration procedures for rotating Lorentz-force flowmeters

Author(s):
Hvasta, M. G.; Slighton, N. T.; Kolemen, E.; Fisher, A. E.
Abstract:
Rotating Lorentz-force flowmeters are a novel and useful technology with a range of applications in a variety of different industries. However, calibrating these flowmeters can be challenging, time-consuming, and expensive. In this paper, simple calibration procedures for rotating Lorentz-force flowmeters are presented. These procedures eliminate the need for expensive equipment, numerical modeling, redundant flowmeters, and system down-time. The calibration processes are explained in a step-by-step manner and compared to experimental results.
Type:
Dataset
Issue Date:
2017

237. Study of liquid metal surface wave damping in the presence of magnetic fields and electrical currents

Author(s):
Fisher, A.E.; Hvasta, M.G.; Kolemen, E.
Abstract:
Experiments and predictions of surface wave damping in liquid metal due to a surface aligned magnetic field and externally regulated j × B force are presented. Fast-flowing, liquid-metal plasma facing components (LM-PFCs) are a proposed alternative to solid PFCs that are unable to handle the high heat flux, thermal stresses, and radiation damage in a tokamak. The significant technical challenges associated with LM-PFCs compared to solid PFCs are justified by greater heat flux management, self-healing properties, and reduced particle recycling. However, undesirable engineering challenges such as evaporation and splashing of the liquid metal introduce excessive impurities into the plasma and degrade plasma performance. Evaporation may be avoided through high-speed flow that limits temperature rise of the liquid metal by reducing heat flux exposure time, but as flow speed increases the surface may become more turbulent and prone to splashing and uneven surfaces. Wave damping is one mechanism that reduces surface disturbance and thus the chances of liquid metal impurity introduction into the plasma. Experiments on the Liquid Metal eXperiment Upgrade (LMX-U) examined damping under the influence of transverse magnetic fields and vertically directed Lorentz force.
Type:
Dataset
Issue Date:
March 2019

238. Experimental demonstration of hydraulic jump control in liquid metal channel flow using Lorentz force

Author(s):
Fisher, Adam; Kolemen, Egemen; Hvasta, Mike
Abstract:
In this paper, hydraulic jump control using electromagnetic force in a liquid metal flow is presented. The control methods used give insight into the hydraulic jump behavior in the presence of magnetic fields and electrical currents. Flowing liquid metals is a proposed solution to heat flux challenges posed in fusion reactors, specifically the tokamak. Unfortunately, thin, fast-flowing liquid metal divertor concepts for fusion reactors are susceptible to hydraulic jumps that drastically reduce the liquid metal flow speed, leading to potential problems such as excessive evaporation, unsteady power removal, and possible plasma disruption. Highly electrically conductive flows within the magnetic fields do not exhibit traditional hydraulic jump behavior. There is very little research investigating the use of externally injected electrical currents and magnetic fields to control liquid metal hydraulic jumps. By using externally injected electrical currents and a magnetic field, a Lorentz force (also referred to as j × B force) may be generated to control the liquid metal jump behavior. In this work, a free-surface liquid metal—GaInSn eutectic or “galinstan”—flow through an electrically insulating rectangular duct was investigated. It was shown that applying a Lorentz force has a repeatable and predictable impact on the hydraulic jump, which can be used for liquid metal control within next-generation fusion reactors.
Type:
Dataset
Issue Date:
2018

240. Large-Eddy Simulation Results for Half Ice / Half Water Surfaces

Author(s):
Fogarty, Joseph
Abstract:
Large-eddy simulations were employed over half-ice and half-water surfaces, with varying surface temperatures, wind speeds, directions, as to test if the atmospheric interaction with the heterogeneous surface can be predicted via a heterogeneity Richardson number. This dataset was used to determine that surface heat fluxes over ice, water, and the aggregate surface seem to be captured reasonably well by the wind direction and the heterogeneity Richardson number, but the mean wind and turbulent kinetic energy (TKE) profiles were not, suggesting that not only the difference in stability between the two surface, but also the individual stabilities over each surface influence the dynamics.
Type:
Dataset
Issue Date:
24 May 2023

241. Large-Eddy Simulation and Statistical Metric Results for Patterned Sea Ice Surfaces

Author(s):
Fogarty, Joseph
Abstract:
Large-eddy simulations were employed over five different sea ice patterns, with a constant ice fraction, to test if the overlying atmospheric boundary layer (ABL) dynamics and thermodynamics differs. The results of these simulations were used to determine that there were differences in vertical heat flux, momentum flux, and horizontal wind speed, and that more surface information is needed to predict the ABL over the sea ice surface. To see what other surface information is needed, twenty-two landscape metrics were calculated over forty-four different maps at differing resolutions, using the FRAGSTATs program. The results of that analysis are available in a .csv file in this dataset.
Type:
Dataset
Issue Date:
August 2023

242. Laboratory study of low-beta forces in arched, line-tied magnetic flux ropes

Author(s):
Myers, Clayton; Yamada, Masaaki; Ji, Hantao; Yoo, Jongsoo; Jara-Almonte, Jonathan; Fox, William
Abstract:
The loss-of-equilibrium is a solar eruption mechanism whereby a sudden breakdown of the magnetohydrodynamic force balance in the Sun's corona ejects a massive burst of particles and energy into the heliosphere. Predicting a loss-of-equilibrium, which has more recently been formulated as the torus instability, relies on a detailed understanding of the various forces that hold the pre-eruption magnetic flux rope in equilibrium. Traditionally, idealized analytical force expressions are used to derive simplified eruption criteria that can be compared to solar observations and modeling. What is missing, however, is a validation that these idealized analytical force expressions can be applied to the line-tied, low-aspect-ratio conditions of the corona. In this paper, we address this shortcoming by using a laboratory experiment to study the forces that act on long-lived, arched, line-tied magnetic flux ropes. Three key force terms are evaluated over a wide range of experimental conditions: (1) the upward hoop force; (2) the downward strapping force; and (3) the downward toroidal field tension force. First, the laboratory force measurements show that, on average, the three aforementioned force terms cancel to produce a balanced line-tied equilibrium. This finding validates the laboratory force measurement techniques developed here, which were recently used to identify a dynamic toroidal field tension force that can prevent flux rope eruptions [Myers et al., Nature 528, 526 (2015)]. The verification of magnetic force balance also confirms the low-beta assumption that the plasma thermal pressure is negligible in these experiments. Next, the measured force terms are directly compared to their corresponding analytical expressions. While the measured and analytical forces are found to be well correlated, the low-aspect-ratio, line-tied conditions in the experiment are found to both reduce the measured hoop force and increase the measured tension force with respect to analytical expectations. These two co-directed effects combine to generate laboratory flux rope equilibria at lower altitudes than are predicted analytically. Such considerations are expected to modify the loss-of-equilibrium eruption criteria for analogous flux ropes in the solar corona.
Type:
Dataset
Issue Date:
November 2016

243. Quasi-static and dynamic magnetic tension forces in arched, line-tied magnetic flux ropes

Author(s):
Myers, Clayton; Yamada, Masaaki; Ji, Hantao; Yoo, Jongsoo; Jara-Almonte, Jonathan; Fox, William
Abstract:
Solar eruptions are often driven by magnetohydrodynamic instabilities such as the torus and kink instabilities that act on line-tied magnetic flux ropes. Recent laboratory experiments designed to study these eruptive instabilities have demonstrated the key role of both dynamic (Myers et al 2015 Nature 528, 526) and quasi-static (Myers et al 2016 Phys. Plasmas, in press) magnetic tension forces in contributing to the equilibrium and stability of line-tied magnetic flux ropes. In this paper, we synthesize these laboratory results and explore the relationship between the dynamic and quasi-static tension forces. While the quasi-static tension force is found to contribute to the flux rope equilibrium in a number of regimes, the dynamic tension force is substantial mostly in the so-called failed torus regime where magnetic self-organization events prevent the flux rope from erupting.
Type:
Dataset
Issue Date:
December 2016

244. Synergy of Coupled Kink and Tearing Modes in Fast Ion Transport

Author(s):
Yang, J.; Podesta, M.; Fredrickson, E.
Abstract:
One aspect of the interaction between fast ions and magnetohydrodynamic (MHD) instabilities is the fast ion transport. Coupled kink and tearing MHD instabilities have also been reported to cause fast ion transport. Recently, the ''kick" model has been developed to compute the evolution of the fast ion distribution from the neutral beam injection using instabilities as phase space resonance sources. The goal of this paper is to utilize the kick model to understand the physics of fast ion transport caused by the coupled kink and tearing modes. Soft X-ray diagnostics are used to identify the mode parameters in NSTX. The comparison of neutron rates measured and computed from time-dependent TRANSP simulation with the kick model shows the coupling of kink and tearing mode is important in determination of the fast ion transport. The numerical scan of the mode parameters shows that the relative phase of the kink and tearing modes and the overlapping of kink and tearing mode resonances in the phase space can affect the fast ion transport, suggesting that the synergy of the coupled modes may be causing the fast ion transpor
Type:
Dataset
Issue Date:
February 2021

246. MHD-blob correlations in NSTX

Author(s):
Zweben, S. J.; Fredrickson, E. D.; Myra, J. R.; Podesta, M.; Scotti, F.
Type:
Dataset
Issue Date:
2020

248. Nonlinear growth of magnetic islands by passing fast ions in NSTX

Author(s):
Yang, James; Fredrickson, Eric; Podestà, Mario; Poli, Francesca
Abstract:
The growth of magnetic islands in NSTX is modeled successfully, with the consideration of passing fast ions. It is shown that a good quantitative agreement between simulation and experimental measurement can be achieved when the uncompensated cross-field current induced by passing fast ions is included in the island growth model. The fast ion parameters, along with other equilibrium parameters, are obtained self-consistently using the TRANSP code with the assumptions of the ‘kick’ model (Podestà et al 2017 Plasma Phys. Control. Fusion 59 095008). The results show that fast ions can contribute to overcoming the stabilizing effect of polarization current for magnetic island growth.
Type:
Dataset
Issue Date:
2022

250. Simulating pitch angle scattering using an explicitly solvable energy-conserving algorithm

Author(s):
Zhang, Xin; Fu, Yichen; Qin, Hong
Abstract:
Particle distribution functions evolving under the Lorentz operator can be simulated with the Langevin equation for pitch angle scattering. This approach is frequently used in particle based Monte-Carlo simulations of plasma collisions, among others. However, most numerical treatments do not guarantee energy conservation, which may lead to unphysical artifacts such as numerical heating and spectra distortions. We present a novel structure-preserving numerical algorithm for the Langevin equation for pitch angle scattering. Similar to the well-known Boris algorithm, the proposed numerical scheme takes advantage of the structure-preserving properties of the Cayley transform when calculating the velocity-space rotations. The resulting algorithm is explicitly solvable, while preserving the norm of velocities down to machine precision. We demonstrate that the method has the same order of numerical convergence as the traditional stochastic Euler-Maruyama method.
Type:
Dataset
Issue Date:
September 2020

254. Climate Impacts from Large Volcanic Eruptions in a High-resolution Climate Model: the Importance of Forcing Structure

Author(s):
Yang, Wenchang; Vecchi, Gabriel; Fueglistaler, Stephan; Horowitz, Larry; Luet, David; Muñoz, Ángel; Paynter, David; Underwood, Seth
Abstract:
Explosive volcanic eruptions have large climate impacts, and can serve as observable tests of the climatic response to radiative forcing. Using a high resolution climate model, we contrast the climate responses to Pinatubo, with symmetric forcing, and those to Santa Maria and Agung, which had meridionally asymmetric forcing. Although Pinatubo had larger global-mean forcing, asymmetric forcing strongly shifts the latitude of tropical rainfall features, leading to larger local precipitation/TC changes. For example, North Atlantic TC activity over is enhanced/reduced by SH-forcing (Agung)/NH-forcing (Santa Maria), but changes little in response to the Pinatubo forcing. Moreover, the transient climate sensitivity estimated from the response to Santa Maria is 20% larger than that from Pinatubo or Agung. This spread in climatic impacts of volcanoes needs to be considered when evaluating the role of volcanoes in global and regional climate, and serves to contextualize the well-observed response to Pinatubo.
Type:
Dataset
Issue Date:
2019

255. Data for Nature Climate Change article 'Regional dry-season climate changes due to three decades of Amazonian deforestation'

Author(s):
Khanna, Jaya; Medvigy, David; Fueglistaler, Stephan; Walko, Robert
Abstract:
More than 20% Amazon rainforest has been cleared in the past three decades triggering important hydroclimatic changes. Small-scale (~few kilometers) deforestation in the 1980s has caused thermally-triggered atmospheric circulations that increase regional cloudiness and precipitation frequency. However, these circulations are predicted to diminish as deforestation increases. Here we use multi-decadal satellite records and numerical model simulations to show a regime shift in the regional hydroclimate accompanying increasing deforestation in Rondônia, Brazil. Compared to the 1980s, present-day deforested areas in downwind western Rondônia are found to be wetter than upwind eastern deforested areas during the local dry season. The resultant precipitation change in the two regions is approximately ±25% of the deforested area mean. Meso-resolution simulations robustly reproduce this transition when forced with increasing deforestation alone, showing a negligible role of large-scale climate variability. Furthermore, deforestation-induced surface roughness reduction is found to play an essential role in the present-day dry season hydroclimate. Our study illustrates the strong scale-sensitivity of the climatic response to Amazonian deforestation and suggests that deforestation is sufficiently advanced to have caused a shift from a thermally- to a dynamically-driven hydroclimatic regime.
Type:
Dataset and Software
Issue Date:
2017

256. Why is El Nino warm?

Author(s):
Hogikyan, Allison; Resplandy, Laure; Yang, Wenchang; Fueglistaler, Stephan
Type:
Dataset
Issue Date:
2021

258. Dataset for China's foreign direct investment in the global power sector

Author(s):
Li, Zhongshu; Gallagher, Kevin P.; Mauzerall, Denise L.
Abstract:
The dataset include a list of power projects outside of China that receive Chinese foreign direct investment from 2000 to 2018. Detailed information including project capacity, location, share of Chinese ownership, type of power generating technologies are collected for each power project.
Type:
Dataset
Issue Date:
January 2020

259. Data from "Vapor-liquid equilibrium of water with the MB-pol many-body potential"

Author(s):
Muniz, Maria Carolina; Gartner III, Thomas E.; Riera, Marc; Knight, Christopher; Yue, Shuwen; Paesani, Francesco; Panagiotopoulos, Athanassios Z.
Abstract:
This dataset contains all data (including input files, simulation trajectories as well as other data files and analysis scripts) related to the publication "Vapor-liquid equilibrium of water with the MB-pol many-body potential" by Muniz et al. in preparation (2021). In this work, we assessed the performance of the MB-pol many-body potential with respect to water's vapor-liquid equilibrium properties. Through the use of direct coexistence molecular dynamics, we calculated properties such as coexistence densities, surface tension, vapor pressures and enthalpy of vaporization. We found that MB-pol is able to predict these properties in good agreement with experimental data. The results attest to the chemical accuracy of MB-pol and its large range of application across water's phase diagram.
Type:
Dataset
Issue Date:
2021

260. Data from "Liquid-liquid transition in water from first principles"

Author(s):
Gartner, Thomas
Abstract:
This dataset contains all data relevant to a forthcoming publication in which we used molecular simulation methods to study the phase behavior of supercooled water. The dataset contains simulation input and output files, processed data files, and image files used to create all plots in the manuscript. Python analysis scripts are also included, including instructions for how to re-generate all plots in the manuscript.
Type:
Dataset
Issue Date:
26 July 2022

262. Remote-sensing gas measurements with coherent Rayleigh-Brillouin scattering

Author(s):
Gerakis, A.; Shneider, M. N.; Stratton, B. C.
Abstract:
We measure the coherent Rayleigh-Brillouin scattering (CRBS) signal integral as a function of the recorded gas pressure in He, Co2, SF6, and air, and we confirm the already established quadratic dependence of the signal on the gas density. We propose the use of CRBS as an effective diagnostic for the remote measurement of gas’ density (pressure) and temperature, as well as polarizability, for gases of known composition.
Type:
Dataset
Issue Date:
2016

264. Data for: 'Facies control on carbonate δ13C on the Great Bahama Bank'

Author(s):
Geyman, Emily C.; Maloof, Adam C.
Abstract:
The carbon isotopic (δ13C) composition of shallow-water carbonates often is interpreted to reflect the δ13C of the global ocean and is used as a proxy for changes in the global carbon cycle. However, local platform processes, in addition to meteoric and marine diagenesis, may decouple carbonate δ13C from that of the global ocean. To shed light on the extent to which changing sediment grain composition may produce δ13C shifts in the stratigraphic record, we present new δ13C measurements of benthic foraminifera, solitary corals, calcifying green algae, ooids, coated grains, and lime mud from the modern Great Bahama Bank (GBB). This survey of a modern carbonate environment reveals δ13C variability comparable to the largest δ13C excursions in the last two billion years of Earth history.
Type:
Dataset
Issue Date:
6 May 2021

267. Developments on two lithium vapor-box linear test-stand experiments

Author(s):
Schwartz, Jacob A.; Goldston, Robert J.
Abstract:
The lithium vapor-box divertor is a possible fusion power exhaust solution.It uses condensation pumping to create a gradient of vapor density in a divertor slot; this should allow a stable detachment front without active feedback.As initial explorations of the concept, two test stands which take the form of three connected cylindrical stainless steel boxes are being developed: one without plasma at PPPL, to test models of lithium evaporation and flow; and one for the linear plasma device Magnum-PSI (at DIFFER in Eindhoven, The Netherlands) to test the ability of a lithium vapor cloud to induce volumetric detachment and redistribute the plasma power.The first experiment uses boxes with diameters of 6 cm, joined by apertures with diameters of 2.2 cm. Up to 1 g of Li is placed in one box, which is heated to up to 600 degrees C. The Li evaporates, then flows to and condenses in the two other, cooler boxes over several minutes. The quantity of Li transported is assessed by weighing the boxes before and after the heating cycle, and is compared to the quantity predicted to flow for the box at its measured temperature using a Direct Simulation Monte Carlo code, SPARTA. With good experimental conditions, the two values agree to within 15%.The experiment on Magnum-PSI is in the conceptual design stage.The design is assessed by simulations using the code B2.5-Eunomia.They show that when the hydrogen-ion plasma beam, with n_e = 4e20 per cubic meter, T_e = 1.5 eV, and r = 1 cm, is passed through a 16 cm long, 12 Pa, 625 degree C Li vapor cloud, the plasma heat flux and pressure on the target are significantly reduced compared to the case without Li.With the Li present, the plasma is cooled by excitation of Li neutrals followed by radiation until it volumetrically recombines, lowering the heat flux from 3.7 MW/m^2 to 0.13 MW/m^2, and the pressure is reduced by 93%, largely by collisions of hydrogen ions with neutral Li.
Type:
Dataset
Issue Date:
January 2021

268. Methane Emissions from Natural Gas Vehicles in China

Author(s):
Pan, Da; Tao, Lei; Golston, Levi; Miller, David; Zhu, Tong; Qin, Yue; Zhang, Yan; Mauzerall, Denise
Abstract:
Natural gas vehicles (NGVs) have been promoted in China to mitigate air pollution, yet our measurements and analyses show that NGV growth in China may have significant negative impacts on climate change. We conducted real-world vehicle emission measurements in China and found high methane emissions from heavy-duty NGVs (90% higher than current emission limits). These emissions have been ignored in previous emission estimates, leading to biased results. Applying our observations to life-cycle analyses, we found that switching to NGVs from conventional vehicles in China has led to a net increase in greenhouse gas (GHG) emissions since 2000. With scenario analyses, we also show that the next decade will be critical for China to reverse the trend with the upcoming China VI standard for heavy-duty vehicles. Implementing and enforcing the China VI standard is challenging, and the method demonstrated here can provide critical information regarding the fleet-level CH4 emissions from NGVs.
Type:
Dataset
Issue Date:
2020

269. TIGRESS simulation data

Author(s):
Kim, Chang-Goo; Ostriker, Eve; Gong, Munan; Kim, Jeong-Gyu
Abstract:
We present the public data release of the TIGRESS (Three-phase Interstellar Medium in Galaxies Resolving Evolution with Star Formation and Supernova Feedback) simulations. This release includes simulations representing the solar neighborhood environment at spatial resolutions of 2 and 4 pc. The original magneto-hydrodynamic simulation data is published along with data products from post-processing, including chemistry, CO emission line, and photoionization (HII regions). Data reading and analysis examples are provided in Python.
Type:
Dataset
Issue Date:
6 September 2022

274. Data and code for “Structured foraging of soil predators unveils functional responses to bacterial defenses”

Author(s):
Gregor, Thomas; Rossine, Fernando
Abstract:
Microscopy images are part of a paper entitled "Structured foraging of soil predators unveils functional responses to bacterial defenses" by Fernando Rossine, Gabriel Vercelli, Corina Tarnita, and Thomas Gregor. For detailed acquisition methods see the paper. Experiments were performed between 2019 and 2020 at Princeton University. Two types of images are provided, macroscopic and microscopic widefiled Images. Macroscopic images all show Petri dishes covered in fluorescent bacteria being consumed by amoebae. Images are shown for D. discoideum, P. violaceum, and A. castellanii. Images depicting drug treatments (Nystatin and Fluorouracil) were obtained using D. discoideum. Images used for the creation of a profile were all taken within 30 minutes of each other. Within each directory numbered images are independent replicates. The raw video directory contains time series for dishes under drug treatments. Each numbered folder is a sequence of photos (taken 30 minutes apart of each other) of a single dish. Microscopic images all show amoebae consuming bacteria on a petri dish. The 45 minute videos show either edge cells (located at the edge of amoebae colonies), or inner cells (located 2.5 millimeters towards the center of the colony, from the edge). Videos are confocal stacks, with bacteria showing in green and amoebae appearing as black holes within the bacterial lawn. As was for the macroscopic images, images are shown for D. discoideum, P. violaceum, and A. castellanii. Images depicting drug treatments (Nystatin and Fluorouracil) were obtained using D. discoideum.
Type:
Dataset and Software
Issue Date:
11 November 2022

276. Data for food consumption strategies in China

Author(s):
Guo, Yixin; Mauzerall, Denise; He, Pan
Abstract:
This dataset provides the data generated during the project analyzing ‘Food Consumption Strategies for Addressing Air Pollution, Climate Change, Water Use, and Public Health in China’. It includes the code for generating the alternative dietary scenarios, for analyzing the health impacts of alternative diets, and for visualization of results.
Type:
Dataset
Issue Date:
31 October 2020

279. The Molino Suite of Galaxy Mock Catalogs

Author(s):
Hahn, ChangHoon
Abstract:
The Molino suite contains 75,000 galaxy mock catalogs designed to quantify the information content of any cosmological observable for a redshift-space galaxy sample. They are constructed from the Quijote N-body simulations (Villaescusa-Navarro et al. 2020) using the standard Zheng et al. (2007) Halo Occupation Distribution (HOD) model. The fiducial HOD parameters are based on the SDSS high luminosity samples. The suite contains 15,000 mocks at the fiducial cosmology and HOD parameters for covariance matrix estimation. It also includes (500 N-body realizations) x (5 HOD realizations)=2,500 mocks at 24 other parameter values to estimate the derivative of the observable with respect to six cosmological parameters (Omega_m, Omega_b, h, n_s, sigma_8, and M_nu) and five HOD parameters (logMmin, sigma_logM, log M_0, alpha, and log M_1). Using the covariance matrix and derivatives calculated from Molino, one can derive Fisher matrix forecasts on the cosmological parameters marginalized over HOD parameters.
Type:
Dataset
Issue Date:
November 2020

281. Application of transient CHI plasma startup to future ST and AT devices

Author(s):
Hammond, K.C.; Raman, R.; Jardin, S.C.
Abstract:
Employment of non-inductive plasma start-up techniques would considerably simplify the design of a spherical tokamak fusion reactor. Transient coaxial helicity injection (CHI) is a promising method, expected to scale favorably to next-step reactors. However, the implications of reactor-relevant parameters on the initial breakdown phase for CHI have not yet been considered. Here, we evaluate CHI breakdown in reactor-like configurations using an extension of the Townsend avalanche theory. We find that a CHI electrode concept in which the outer vessel wall is biased to achieve breakdown, while previously successful on NSTX and HIT-II, may exhibit a severe weakness when scaled up to a reactor. On the other hand, concepts which employ localized biasing electrodes such as those used in QUEST would avoid this issue. Assuming that breakdown can be successfully attained, we then apply scaling relationships to predict plasma parameters attainable in the transient CHI discharge. Assuming the use of 1 Wb of injector flux, we find that plasma currents of 1 MA should be achievable. Furthermore, these plasmas are expected to Ohmically self-heat with more than 1 MW of power as they decay, facilitating efficient hand-off to steady-state heating sources. These optimistic scalings are supported by TSC simulations.
Type:
Dataset
Issue Date:
February 2019

282. A thermodynamic phase transition in magnetic reconnection

Author(s):
Jara-Almonte, Jonathan; Hantao, Ji
Abstract:
Data supporting the manuscript "A thermodynamic phase transition in magnetic reconnection" published in Physical Review Letters.
Type:
Dataset
Issue Date:
7 July 2021

283. Amplification of local changes along the timescale processing hierarchy

Author(s):
Yeshurun, Yaara; Nguyen, Mai; Hasson, Uri
Abstract:
Small changes in word choice can lead to dramatically different interpretations of narratives. How does the brain accumulate and integrate such local changes to construct unique neural representations for different stories? In this study we created two distinct narratives by changing only a few words in each sentence (e.g. “he” to “she” or “sobbing” to “laughing”) while preserving the grammatical structure across stories. We then measured changes in neural responses between the two stories. We found that the differences in neural responses between the two stories gradually increased along the hierarchy of processing timescales. For areas with short integration windows, such as early auditory cortex, the differences in neural responses between the two stories were relatively small. In contrast, in areas with the longest integration windows at the top of the hierarchy, such as the precuneus, temporal parietal junction, and medial frontal cortices, there were large differences in neural responses between stories. Furthermore, this gradual increase in neural difference between the stories was highly correlated with an area’s ability to integrate information over time. Amplification of neural differences did not occur when changes in words did not alter the interpretation of the story (e.g. “sobbing” to “crying”). Our results demonstrate how subtle differences in words are gradually accumulated and amplified along the cortical hierarchy as the brain constructs a narrative over time.
Type:
Dataset
Issue Date:
August 2017

284. Data for "Caught in the Crossfire: Fears of Chinese-American Scientists"

Author(s):
Xie, Yu; Lin, Xihong; Li, Ju; He, Qian; Huang, Junming
Abstract:
This dataset encompasses two distinct sets of data analyzed in the study, namely Asian American Scholar Forum survey data and Microsoft Academic Graph bibleometrics data: Yu Xie, Xihong Lin, Ju Li, Qian He, Junming Huang, Caught in the Crossfire: Fears of Chinese-American Scientists, Proceedings of the National Academy of Sciences, in press (2023).
Type:
Dataset
Issue Date:
May 2023

286. Data and code for 'Hydrological cycle amplification reshapes warming-driven oxygen loss in Atlantic Ocean'

Author(s):
Hogikyan, Allison
Abstract:
Physical and biogeochemical variables from the NOAA-GFDL Earth System Model 2M experiments (pre-processed), previously published observation-based datasets, and code to reproduce figures from these datasets, used for the study 'Hydrological cycle amplification reshapes warming-driven oxygen loss in Atlantic Ocean'.
Type:
Dataset and Software
Issue Date:
June 2023

288. Data for: Three-Dimensional Morphometry of Ooids in Oolites: a new tool for more accurate and precise paleoenvironmental interpretation

Author(s):
Howes, Bolton; Mehra, Akshay; Maloof, Adam
Abstract:
The prevalence of ooids in the stratigraphic record, and their association with shallow-water carbonate environments, make ooids an important paleoenvironmental indicator. Recent advances in the theoretical understanding of ooid morphology, along with empirical studies from Turks and Caicos, Great Salt Lake, and The Bahamas, have demonstrated that the morphology of ooids is indicative of depositional environment and hydraulic conditions. To apply this knowledge from modern environments to the stratigraphic record of Earth history, researchers measure the size and shape of lithified ooids on two-dimensional surfaces (i.e., thin sections or polished slabs), often assuming that random 2D slices intersect the nuclei and that the orientation of the ooids is known. Here we demonstrate that these assumptions rarely are true, resulting in errors of up to 35% on metrics like major axis length. We present a method for making 3D reconstructions by serial grinding and imaging, which enables accurate measurement of the morphology of individual ooids within an oolite, as well as the sorting and porosity of a sample. We also provide three case studies that use the morphology of ooids in oolites to extract environmental information. Each case study demonstrates that 2D measurements can be useful if the environmental signal is large relative to the error from 2D measurements. However, 3D measurements substantially improve the accuracy and precision of environmental interpretations. This study focuses on oolites, but errors from 2D measurements are not unique to oolites; this method can be used to extract accurate grain and porosity measurements from any lithified granular sample.
Type:
Dataset
Issue Date:
22 February 2021

289. Multi-Fluid and Kinetic Models of Partially Ionized Magnetic Reconnection

Author(s):
Jara-Almonte, J.; Murphy, N.A.; Ji, H.
Abstract:
Magnetic reconnection in partially ionized plasmas is a ubiquitous and important phenomena in both laboratory and astrophysical systems. Here, simulations of partially ionized magnetic reconnection with well-matched initial conditions are performed using both multi-fluid and fully-kinetic approaches. Despite similar initial conditions, the time-dependent evolution differs between the two models. In multi-fluid models, the reconnection rate locally obeys either a decoupled Sweet-Parker scaling, where neutrals are unimportant, or a fully coupled Sweet-Parker scaling, where neutrals and ions are strongly coupled, depending on the resistivity. In contrast, kinetic models show a faster reconnection rate that is proportional to the fully-coupled, bulk Alfv\'en speed, $v_A^\star$. These differences are interpreted as the result of operating in different collisional regimes. Multi-fluid simulations are found to maintain $\nu_{ni}L/v_A^\star \gtrsim 1$, where $\nu_{ni}$ is the neutral-ion collision frequency and $L$ is the time-dependent current sheet half-length. This strongly couples neutrals to the reconnection outflow, while kinetic simulations evolve to allow $\nu_{ni}L/v_A^\star < 1$, decoupling neutrals from the reconnection outflow. Differences in the way reconnection is triggered may explain these discrepancies.
Type:
Dataset
Issue Date:
2021

293. Coupling between Alfven wave and Kelvin-Helmholtz waves in the low latitude boundary layer

Author(s):
Kim, Eun-Hwa; Johnson, Jay; Nykyri, Katariina
Abstract:
The Kelvin-Helmholtz (KH) instability of magnetohydrodynamic surface waves at the low latitude boundary layer is examined using both an eigenfrequency analysis and a time-dependent wave simulation. The analysis includes the effects of sheared flow and Alfven velocity gradient. When the magnetosheath flows are perpendicular to the ambient magnetic field direction, unstable KH waves that propagate obliquely to the sheared flow direction occur at the sheared flow surface when the Alfv\'en Mach number is higher than an instability threshold. Including a shear transition layer between the magnetosphere and magnetosheath leads to secondary KH waves (driven by the sheared flow) that are coupled to the resonant surface Alfven wave. There are remarkable differences between the primary and the secondary KH waves including wave frequency, the growth rate, and the ratio between transverse and the compressional component. The secondary KH wave energy is concentrated near the shear Alfven wave frequency at the magnetosheath with a lower frequency than the primary KH waves. Although the growth rate of the secondary KH waves is lower than the primary KH waves, the threshold condition is lower, so it is expected that these types of waves will dominate at lower Mach number. Because the transverse component of the secondary KH waves is stronger than the primary KH waves, more efficient wave energy transfer from the boundary layer to the inner magnetosphere is also predicted.
Type:
Dataset
Issue Date:
December 2021

295. Quantitative imaging of carbon dimer precursor for nanomaterial synthesis in the carbon arc

Author(s):
Vekselman, V.; Khrabry, A.; Kaganovich, I.; Stratton, B.; Selinsky, R. S.; Raitses, Y.
Abstract:
Delineating the dominant processes responsible for nanomaterial synthesis in a plasma environment requires measurements of the precursor species contributing to the growth of nanostructures. We performed comprehensive measurements of spatial and temporal profiles of carbon dimers in sub-atmospheric-pressure carbon arc by laser-induced fluorescence. Measured spatial profiles of carbon dimers coincide with the growth region of carbon nanotubes (Fang et al 2016 Carbon 107 273-80) and vary depending on the arc operation mode, which is determined by the discharge current and the ablation rate of the graphite anode. The carbon dimer density profile exhibits large spatial and time variations due to motion of the arc core. A comparison of the experimental data with the 2D simulation results of self-consistent arc modeling shows a good agreement. The model predicts well the main processes determining spatial profiles of carbon dimers.
Type:
Dataset
Issue Date:
January 2018

297. Plasma Facing Components with Capillary Porous System and Liquid Metal Coolant Flow

Author(s):
Khodak, Andrei; Maingi, Rajesh
Abstract:
Liquid metal can create a renewable protective surface on plasma facing components (PFC), with an additional advantage of deuterium pumping and the prospect of tritium extraction if liquid lithium (LL) is used and maintained below 450 C, the temperature above which LL vapor pressure begins to contaminate the plasma. LM can also be utilized as an efficient coolant, driven by the Lorentz force created with the help of the magnetic field in fusion devices. Capillary porous systems can serve as a conduit of LM and simultaneously provide stabilization of the LM flow, protecting against spills into the plasma. Recently a combination of a fast-flowing LM cooling system with a porous plasma facing wall (CPSF) was investigated [Khodak and Maingi (2021)]. The system takes an advantage of a magnetohydrodynamics velocity profile, as well as attractive LM properties to promote efficient heat transfer from the plasma to the LL at low pumping energy cost, relative to the incident heat flux on the PFC. In case of a disruption leading to excessive heat flux from the plasma to the LM PFCs, LL evaporation can stabilize the PFC surface temperature, due to high evaporation heat and apparent vapor shielding. The proposed CPSF was optimized analytically for the conditions of a Fusion Nuclear Science Facility [Kessel et al. (2019)]: 10T toroidal field and 10 MW/m2 peak incident heat flux. Computational fluid dynamics analysis confirmed that a CPSF system with 2.5 mm square channels can pump enough LL so that no additional coolant is needed.
Type:
Dataset and Image
Issue Date:
2021

298. Data for: "Structure and Density of Silicon Carbide to 1.5 TPa and Implications for Extrasolar Planets"

Author(s):
Kim, Donghoon
Abstract:
There has been considerable recent interest in the high-pressure behavior of silicon carbide, a potential major constituent of carbon-rich exoplanets. In this work, the atomic-level structure of SiC was determined through in situ X-ray diffraction under laser-driven ramp compression up to 1.5 TPa; stresses more than seven times greater than previous static and shock data. Here we show that the B1-type structure persists over this stress range and we have constrained its equation of state (EOS). Using this data we have determined the first experimentally based mass-radius curves for a hypothetical pure SiC planet. Interior structure models are constructed for planets consisting of a SiC-rich mantle and iron-rich core. Carbide planets are found to be ~10% less dense than corresponding terrestrial planets.
Type:
Dataset
Issue Date:
28 April 2022

300. Code and data from "Comparative genomic analysis reveals varying levels of mammalian adaptation to coronavirus infections"

Author(s):
King, Sean
Abstract:
Severe acute respiratory coronavirus 2 (SARS-CoV-2), the causative agent of COVID-19, is of zoonotic origin. Evolutionary analyses assessing whether coronaviruses similar to SARS-CoV-2 infected ancestral species of modern-day animal hosts could be useful in identifying additional reservoirs of potentially dangerous coronaviruses. We reasoned that if a clade of species has been repeatedly exposed to a virus, then their proteins relevant for viral entry may exhibit adaptations that affect host susceptibility or response. We perform comparative analyses across the mammalian phylogeny of angiotensin-converting enzyme 2 (ACE2), the cellular receptor for SARS-CoV-2, in order to uncover evidence for selection acting at its binding interface with the SARS-CoV-2 spike protein. We uncover that in rodents there is evidence for adaptive amino acid substitutions at positions comprising the ACE2-spike interaction interface, whereas the variation within ACE2 proteins in primates and some other mammalian clades is not consistent with evolutionary adaptations. We also analyze aminopeptidase N (APN), the receptor for the human coronavirus 229E, a virus that causes the common cold, and find evidence for adaptation in primates. Altogether, our results suggest that the rodent and primate lineages may have had ancient exposures to viruses similar to SARS-CoV-2 and HCoV-229E, respectively. Included in this repository are the instructions and corresponding code required to build the dataset and run the analysis in the manuscript.
Type:
Dataset
Issue Date:
28 September 2021