Liquid metal can create a renewable protective surface on plasma facing components (PFC), with an additional advantage of deuterium pumping and the prospect of tritium extraction if liquid lithium (LL) is used and maintained below 450 C, the temperature above which LL vapor pressure begins to contaminate the plasma. LM can also be utilized as an efficient coolant, driven by the Lorentz force created with the help of the magnetic field in fusion devices. Capillary porous systems can serve as a conduit of LM and simultaneously provide stabilization of the LM flow, protecting against spills into the plasma. Recently a combination of a fast-flowing LM cooling system with a porous plasma facing wall (CPSF) was investigated [Khodak and Maingi (2021)]. The system takes an advantage of a magnetohydrodynamics velocity profile, as well as attractive LM properties to promote efficient heat transfer from the plasma to the LL at low pumping energy cost, relative to the incident heat flux on the PFC. In case of a disruption leading to excessive heat flux from the plasma to the LM PFCs, LL evaporation can stabilize the PFC surface temperature, due to high evaporation heat and apparent vapor shielding. The proposed CPSF was optimized analytically for the conditions of a Fusion Nuclear Science Facility [Kessel et al. (2019)]: 10T toroidal field and 10 MW/m2 peak incident heat flux. Computational fluid dynamics analysis confirmed that a CPSF system with 2.5 mm square channels can pump enough LL so that no additional coolant is needed.
Bourrianne, Philippe; Chidzik, Stanley; Cohen, Daniel; Elmer, Peter; Hallowell, Thomas; Kilbaugh, Todd J.; Lange, David; Leifer, Andrew M.; Marlow, Daniel R.; Meyers, Peter D.; Normand, Edna; Nunes, Janine; Oh, Myungchul; Page, Lyman; Periera, Talmo; Pivarski, Jim; Schreiner, Henry; Stone, Howard A.; Tank, David W.; Thiberge, Stephan; Tully, Christopher
The detailed information on the design and construction of the Princeton Open Ventilation Monitor device and software are contained in this data repository. This information consists of the electrical design files, mechanical design files, bill of materials, human subject recording and analysis code, and a copy of the code repository for operating the patient monitors and central station.
Taylor, Jenny A.; Bratton, Benjamin P.; Sichel, Sophie R.; Blair, Kris M.; Jacobs, Holly M.; DeMeester, Kristen E.; Kuru, Erkin; Gray, Joe; Biboy, Jacob; VanNieuwenhze, Michael S.; Vollmer, Waldemar; Grimes, Catherine L.; Shaevitz, Joshua W.; Salama, Nina R.
Helical cell shape is necessary for efficient stomach colonization by Helicobacter pylori, but the molecular mechanisms for generating helical shape remain unclear. We show that the helical centerline pitch and radius of wild-type H. pylori cells dictate surface curvatures of considerably higher positive and negative Gaussian curvatures than those present in straight- or curved-rod bacteria. Quantitative 3D microscopy analysis of short pulses with either N-acetylmuramic acid or D-alanine metabolic probes showed that cell wall growth is enhanced at both sidewall curvature extremes. Immunofluorescence revealed MreB is most abundant at negative Gaussian curvature, while the bactofilin CcmA is most abundant at positive Gaussian curvature. Strains expressing CcmA variants with altered polymerization properties lose helical shape and associated positive Gaussian curvatures. We thus propose a model where CcmA and MreB promote PG synthesis at positive and negative Gaussian curvatures, respectively, and that this patterning is one mechanism necessary for maintaining helical shape.
Extrapolation -- the ability to make inferences that go beyond the scope of one's experiences -- is a hallmark of human intelligence. By contrast, the generalization exhibited by contemporary neural network algorithms is largely limited to interpolation between data points in their training corpora. In this paper, we consider the challenge of learning representations that support extrapolation. We introduce a novel visual analogy benchmark that allows the graded evaluation of extrapolation as a function of distance from the convex domain defined by the training data. We also introduce a simple technique, context normalization, that encourages representations that emphasize the relations between objects. We find that this technique enables a significant improvement in the ability to extrapolate, considerably outperforming a number of competitive techniques.
Dust and starlight have been modeled for the KINGFISH project galaxies. For each pixel in each galaxy, we estimate: (1) dust surface density; (2) q_PAH, the dust mass fraction in PAHs; (3) distribution of starlight intensities heating the dust; (4) luminosity emitted by the dust; and (5) dust luminosity from regions with high starlight intensity. The modeling is as described in the paper "Modeling Dust and Starlight in Galaxies Observed by Spitzer and Herschel: The KINGFISH Sample", by G. Aniano, B.T. Draine, L.K. Hunt, K. Sandstrom, D. Calzetti, R.C. Kennicutt, D.A, Dale, and 26 other authors, accepted for publication in The Astrophysical Journal.
This dataset contains all the data, model and MATLAB codes used to generate the figures and data reported in the article (DOI: 10.1002/2014JD022278). The data was generated during September 2013 and February 2014 using the Ocean-Land-Atmosphere Model also provided with this package. The data was generated using the computational resources supported by the PICSciE OIT High Performance Computing Center and Visualization Laboratory at Princeton University. The dataset contains a pdf Readme file which explains in detail how the data can be used. Users are recommended to go through this file before using the data.