Number of results to display per page
Search Results
202. Quasioptical modeling of wave beams with and without mode conversion: III. Numerical simulations of mode-converting beams
- Author(s):
- K. Yanagihara, I. Y. Dodin, and S. Kubo
- Abstract:
- This work continues a series of papers where we propose an algorithm for quasioptical modeling of electromagnetic beams with and without mode conversion. The general theory was reported in the first paper of this series, where a parabolic partial differential equation was derived for the field envelope that may contain one or multiple modes with close group velocities. In the second paper, we presented a corresponding code PARADE (PAraxial RAy DEscription) and its test applications to single-mode beams. Here, we report quasioptical simulations of mode-converting beams for the first time. We also demonstrate that PARADE can model splitting of two-mode beams. The numerical results produced by PARADE show good agreement with those of one-dimensional full-wave simulations and also with conventional ray tracing (to the extent that one-dimensional and ray-tracing simulations are applicable).
- Type:
- Dataset
- Issue Date:
- August 2019
203. Real-time capable modeling of neutral beam injection on NSTX-U using neural networks
- Author(s):
- Boyer, M.D.; Kaye, S.; Erickson, K.
- Abstract:
- A new model of heating, current drive, torque and other effects of neutral beam injection on NSTX-U that uses neural networks has been developed. The model has been trained and tested on the results of the Monte Carlo code NUBEAM for the database of experimental discharges taken during the first operational campaign of NSTX-U. By projecting flux surface quantities onto empirically derived basis functions, the model is able to efficiently and accurately reproduce the behavior of both scalars, like the total neutron rate and shine through, and profiles, like beam current drive and heating. The model has been tested on the NSTX-U real-time computer, demonstrating a rapid execution time orders of magnitude faster than the Monte Carlo code that is well suited for the iterative calculations needed to interpret experimental results, optimization during scenario development activities, and real-time plasma control applications. Simulation results of a proposed design for a nonlinear observer that embeds the neural network calculations to estimate the poloidal flux profile evolution, as well as effective charge and fast ion diffusivity, are presented.
- Type:
- Dataset
- Issue Date:
- February 2019
204. Reduced Model for Direct Induction Startup Scenario Development on MAST-U and NSTX-U
- Author(s):
- Battaglia, D.J.; Thornton, A.J.; Gerhardt, S.P.; Kirk, A.; Kogan, L; Menard, J.E.
- Abstract:
- A reduced semi-empirical model using time-dependent axisymmetric vacuum field calculations is used to develop the prefill and feed-forward coil current targets required for reliable direct induction (DI) startup on the new MA-class spherical tokamaks, MAST-U and NSTX-U. The calculations are constrained by operational limits unique to each device, such as the geometry of the conductive elements and active coils, power supply specifications and coil heating and stress limits. The calculations are also constrained by semi-empirical models for sufficient breakdown, current drive, equilibrium and stability of the plasma developed from a shared database. A large database of DI startup on NSTX and NSTX-U is leveraged to quantify the requirements for achieving a reliable breakdown (Ip ~ 20 kA). It is observed that without pre-ionization, STs access the large E/P regime at modest loop voltage (Vloop) where the electrons in the weakly ionized plasma are continually accelerating along the open field lines. This ensures a rapid (order millisecond) breakdown of the neutral gas, even without pre-ionization or high-quality field nulls. The timescale of the initial increase in Ip on NSTX is reproduced in the reduced model provided a mechanism for impeding the applied electric field is included. Most discharges that fail in the startup phase are due to an inconsistency in the evolution of the plasma current (Ip) and equilibrium field or loss of vertical stability during the burn-through phase. The requirements for the self-consistent evolution of the fields in the weakly and full-ionized plasma states are derived from demonstrated DI startup on NSTX, NSTX-U and MAST. The predictive calculations completed for MAST-U and NSTX-U illustrate that the maximum Ip ramp rate (dIp/dt) in the early startup phase is limited by the voltage limits on the poloidal field coils on MAST-U and passive vertical stability on NSTX-U.
- Type:
- Dataset
- Issue Date:
- August 2019
205. Sound velocities in shock-synthesized stishovite to 72 GPa
- Author(s):
- Berryman, Eleanor J.; Winey, J. M.; Gupta, Yogendra M.; Duffy, Thomas S.
- Abstract:
- Stishovite (rutile-type SiO2) is the archetype of dense silicates and may occur in post-garnet eclogitic rocks at lower-mantle conditions. Sound velocities in stishovite are fundamental to understanding its mechanical and thermodynamic behavior at high pressure and temperature. Here, we use plate-impact experiments combined with velocity interferometry to determine the stress, density, and longitudinal sound speed in stishovite formed during shock compression of fused silica at 44 GPa and above. The measured sound speeds range from 12.3(8) km/s at 43.8(8) GPa to 9.8(4) km/s at 72.7(11) GPa. The decrease observed at 64 GPa reacts a decrease in the shear modulus of stishovite, likely due to the onset of melting. By 72 GPa, the measured sound speed agrees with the theoretical bulk sound speed indicating loss of all shear stiffness due to complete melting. Our sound velocity results provide direct evidence for shock-induced melting, in agreement with previous pyrometry data.
- Type:
- Dataset
- Issue Date:
- 2019
206. Sowing the Seeds for More Usable Web Archives: A Usability Study of Archive-It
- Author(s):
- Abrams, Samantha; Antracoli, Alexis; Appel, Rachel; Caust-Ellenbogen, Celia; Dennison, Sarah; Duncan, Sumitra; Ramsay, Stefanie
- Abstract:
- In 2017, seven members of the Archive-It Mid-Atlantic Users Group (AITMA) conducted a study of 14 subjects representative of their stakeholder populations to assess the usability of Archive-It, a web archiving subscription service of the Internet Archive. While Archive-It is the most widely-used tool for web archiving, little is known about how users interact with the service. This study intended to teach us what users expect from web archives, which exist as another form of archival material. End-user subjects executed four search tasks using the public Archive-It interface and the Wayback Machine to access archived information on websites from the facilitators’ own harvested collections and provide feedback about their experiences. The tasks were designed to have straightforward pass or fail outcomes, and the facilitators took notes on the subjects’ behavior and commentary during the sessions. Overall, participants reported mildly positive impressions of Archive-It public user interface based on their session. The study identified several key areas of improvement for the Archive-It service pertaining to metadata options, terminology display, indexing of dates, and the site’s search box.
- Type:
- Dataset
- Issue Date:
- 2019
207. Spontaneous multi-keV electron generation in a low-RF-power axisymmetric mirror machine
- Author(s):
- Swanson, C.;Cohen, S.A.
- Abstract:
- Title: Spontaneous multi-keV electron generation in a low-RF-power axisymmetric mirror machine Abstract: X-ray emission shows the existence of multi-keV electrons in low-temperature, low-power, capacitively-coupled RF-heated magnetic-mirror plasmas that also contain a warm (300 eV) minority electron population. Though these warm electrons are initially passing particles, we suggest that collisionless scattering -- mu non-conservation in the static vacuum field -- is responsible for a minority of them to persist in the mirror cell for thousands of transits during which time a fraction are energized to a characteristic temperature of 3 keV, with some electrons reaching energies above 30 keV. A heuristic model of the heating by a Fermi-acceleration-like mechanism is presented, with mu non-conservation in the static vacuum field as an essential feature.
- Type:
- Dataset
- Issue Date:
- May 2019
208. Study of liquid metal surface wave damping in the presence of magnetic fields and electrical currents
- Author(s):
- Fisher, A.E.; Hvasta, M.G.; Kolemen, E.
- Abstract:
- Experiments and predictions of surface wave damping in liquid metal due to a surface aligned magnetic field and externally regulated j × B force are presented. Fast-flowing, liquid-metal plasma facing components (LM-PFCs) are a proposed alternative to solid PFCs that are unable to handle the high heat flux, thermal stresses, and radiation damage in a tokamak. The significant technical challenges associated with LM-PFCs compared to solid PFCs are justified by greater heat flux management, self-healing properties, and reduced particle recycling. However, undesirable engineering challenges such as evaporation and splashing of the liquid metal introduce excessive impurities into the plasma and degrade plasma performance. Evaporation may be avoided through high-speed flow that limits temperature rise of the liquid metal by reducing heat flux exposure time, but as flow speed increases the surface may become more turbulent and prone to splashing and uneven surfaces. Wave damping is one mechanism that reduces surface disturbance and thus the chances of liquid metal impurity introduction into the plasma. Experiments on the Liquid Metal eXperiment Upgrade (LMX-U) examined damping under the influence of transverse magnetic fields and vertically directed Lorentz force.
- Type:
- Dataset
- Issue Date:
- March 2019
209. TRANSP-based Optimization Towards Tokamak Scenario Development
- Author(s):
- W.P. Wehner, E. Schuster, M.D. Boyer, F. Poli
- Abstract:
- An optimization approach that incorporates the predictive transport code TRANSP is proposed for tokamak scenario development. Optimization methods are often employed to develop open-loop control strategies to aid access to high performance tokamak scenarios. In general, the optimization approaches use control-oriented models, i.e. models that are reduced in complexity and prediction accuracy as compared to physics-oriented transport codes such as TRANSP. In the presented approach, an optimization procedure using the TRANSP code to simulate the tokamak plasma is considered for improved predictive capabilities. As a test case, the neutral beam injection (NBI) power is optimized to develop a control strategy that maximizes the non-inductive current fraction during the ramp-up phase for NSTX-U. Simulation studies towards the achievement of non-inductive ramp up in NSTX-U have already been carried out with the TRANSP code. The optimization-based approach proposed in this work is used to maximize the non-inductive current fraction during ramp-up in NSTX-U, demonstrating that the scenario development task can be automated. An additional test case considers optimization of the current ramp rate in DIII-D for obtaining a stationary plasma characterized by a flat loop voltage profile in the flattop phase.
- Type:
- Dataset
- Issue Date:
- April 2019
210. TRANSP-based closed-loop simulations of current profile optimal regulation in NSTX-Upgrade
- Author(s):
- Ilhan, Z.O.; Boyer. M.D.; Schuster, E.
- Abstract:
- Active control of the toroidal current density profile is critical for the upgraded National Spherical Torus eXperiment device (NSTX-U) to maintain operation at the desired high-performance, MHD-stable, plasma regime. Initial efforts towards current density profile control have led to the development of a control-oriented, physics-based, plasma-response model, which combines the magnetic diffusion equation with empirical correlations for the kinetic profiles and the non-inductive current sources. The developed control-oriented model has been successfully tailored to the NSTX-U geometry and actuators. Moreover, a series of efforts have been made towards the design of model-based controllers, including a linear-quadratic-integral optimal control strategy that can regulate the current density profile around a prescribed target profile while rejecting disturbances. In this work, the tracking performance of the proposed current-profile optimal controller is tested in numerical simulations based on the physics-oriented code TRANSP. These high-fidelity closed-loop simulations, which are a critical step before experimental implementation and testing, are enabled by a flexible framework recently developed to perform feedback control design and simulation in TRANSP.
- Type:
- Dataset
- Issue Date:
- March 2019
211. Unsupervised identification of the internal states that shape natural behavior
- Author(s):
- Calhoun, Adam; Pillow, Jonathan; Murthy, Mala
- Type:
- Dataset
- Issue Date:
- 28 May 2019
212. Verification of the global gyrokinetic stellarator code XGC-S for linear ion temperature gradient driven modes
- Author(s):
- Cole M; Hager R; Moritaka T; Dominski J; Kleiber R; Ku S; Lazerson S; Riemann J; Chang C
- Abstract:
- XGC (X-point Gyrokinetic Code) is a whole-volume, total-f gyrokinetic particle-in-cell code developed for modelling tokamaks.In recent work, XGC has been extended to model more general 3D toroidal magnetic configurations, such as stellarators.These improvements have resulted in the XGC-S version.In this paper, XGC-S is benchmarked in the reduced delta-f limit for linear electrostatic ion temperature gradient-driven microinstabilities, which can underlie turbulent transport in stellarators.An initial benchmark of XGC-S in tokamak geometry shows good agreement with the XGC1, ORB5, and global GENE codes.A benchmark between XGC-S and the EUTERPE global gyrokinetic code for stellarators has also been performed, this time in geometry of the optimised stellarator Wendelstein 7-X.Good agreement has been found for the mode number spectrum, mode structure, and growth rate.
- Type:
- Dataset
- Issue Date:
- August 2019
213. Calibrationless rotating Lorentz-force flowmeters for low flow rate applications
- Author(s):
- Hvasta, M. G.; Dudt, D.; Fisher, A. E.; Kolemen, E.
- Abstract:
- A 'weighted magnetic bearing' has been developed to improve the performance of rotating Lorentz-force flowmeters (RLFFs). Experiments have shown that the new bearing reduces frictional losses within a double-sided, disc-style RLFF to negligible levels. Operating such an RLFF under 'frictionless' conditions provides two major benefits. First, the steady-state velocity of the RLFF magnets matches the average velocity of the flowing liquid at low flow rates. This enables an RLFF to make accurate volumetric flow measurements without any calibration or prior knowledge of the fluid properties. Second, due to minimized frictional losses, an RLFF is able to measure low flow rates that cannot be detected when conventional, high-friction bearings are used. This paper provides a brief background on RLFFs, gives a detailed description of weighted magnetic bearings, and compares experimental RLFF data to measurements taken with a commercially available flowmeter.
- Type:
- Dataset
- Issue Date:
- 29 May 2018
214. Collapse of reacted fracture surface decreases permeability and frictional strength
- Author(s):
- Peters, Catherine A.; Spokas, Kasparas
- Abstract:
- Geochemical and geomechanical perturbations of the subsurface caused by the injection of fluids present the risk of leakage and seismicity. This study investigated how flow of acidic fluids affects hydraulic and frictional properties of fractures using experiments with 3.8 cm-long specimens of Eagle Ford shale, a laminated shale with carbonate-rich strata. In low-pressure flow cells, one set of samples was exposed to an acidic brine and another set was exposed to a neutral brine. X-ray computed tomography and x-ray fluorescence analysis revealed that samples exposed to the acidic brine were calcite-depleted and had developed a porous altered layer, while the other set showed little evidence of alteration. After reaction, samples were compacted and sheared in a triaxial cell that supplied normal stress and differential pore pressure at prescribed sliding velocities, independently measuring friction and permeability. During the initial compaction, the porous altered layer collapsed into fine particles that filled the fracture aperture. This effectively impeded flow and sealed the fracture, resulting in a decrease in fracture permeability by 1 to 2 orders of magnitude relative to the compressed unaltered fractures. During shear, the collapsed layer of fine-grained particles prevented the formation of interlocking micro-asperities resulting in lower frictional strength. With regard to subsurface risks, this study showcases how coupled geochemical and geomechanical processes could favorably seal fractures to inhibit leakage, but also could increase the likelihood of induced seismicity. These findings have important implications for geological carbon sequestration, pressurized fluid energy storage, geothermal energy, and other subsurface technologies.
- Type:
- Dataset
- Issue Date:
- 2018
215. Compact steady-state tokamak performance dependence on magnet and core physics limits
- Author(s):
- Menard, J.E.
- Abstract:
- Compact tokamak fusion reactors utilizing advanced high-temperature superconducting magnets for the toroidal field coils have received considerable recent attention due to the promise of more compact devices and more economical fusion energy development. Facilities with combined Fusion Nuclear Science (FNS) and Pilot Plant missions to provide both the nuclear environment needed to develop fusion materials and components while also potentially achieving sufficient fusion performance to generate modest net electrical power are considered. The performance of the tokamak fusion system is assessed using a range of core physics and toroidal field magnet performance constraints to better understand which parameters most strongly influence the achievable fusion performance.
- Type:
- Dataset
- Issue Date:
- December 2018
216. Demonstrating electromagnetic control of free-surface, liquid-metal flows relevant to fusion reactors
- Author(s):
- Hvasta, M. G.; Kolemen, E.; Fisher, A. E.; Ji, H.
- Abstract:
- Plasma-facing components (PFC's) made from solid materials may not be able to withstand the large heat and particle fluxes that will be produced within next-generation fusion reactors. To address the shortcomings of solid PFC's, a variety of liquid-metal (LM) PFC concepts have been proposed. Many of the suggested LM-PFC designs rely on electromagnetic restraint (Lorentz force) to keep free-surface, liquid-metal flows adhered to the interior surfaces of a fusion reactor. However, there is very little, if any, experimental data demonstrating that free-surface, LM-PFC's can actually be electromagnetically controlled. Therefore, in this study, electrical currents were injected into a free-surface liquid-metal that was flowing through a uniform magnetic field. The resultant Lorentz force generated within the liquid-metal affected the velocity and depth of the flow in a controllable manner that closely matched theoretical predictions. These results show the promise of electromagnetic control for LM-PFC's and suggest that electromagnetic control could be further developed to adjust liquid-metal nozzle output, prevent splashing within a tokamak, and alter heat transfer properties for a wide-range of liquid-metal systems.
- Type:
- Dataset
- Issue Date:
- January 2018
217. Design and measurement methods for a lithium vapor box similarity experiment
- Author(s):
- Schwartz, J. A.; Emdee, E. D.; Jaworski, M. A; Goldston, R. J.
- Abstract:
- The lithium vapor box divertor is a concept for handling the extreme divertor heat fluxes in magnetic fusion devices. In a baffled slot divertor, plasma interacts with a dense cloud of Li vapor which radiates and cools the plasma, leading to recombination and detachment. Before testing on a tokamak the concept should be validated: we plan to study detachment and heat redistribution by a Li vapor cloud in laboratory experiments. Mass changes and temperatures are measured to validate a Direct Simulation Monte Carlo model of neutral Li. The initial experiment involves a 5 cm diameter steel box containing 10g of Li held at 650 degrees C as vapor flows out a wide nozzle into a similarly-sized box at a lower temperature. Diagnosis is made challenging by the required material compatibility with lithium vapor. Vapor pressure is a steep function of temperature, so to validate mass flow models to within 10%, absolute temperature to within 4.5K is required. The apparatus is designed to be used with an analytical balance to determine mass transport. Details of the apparatus and methods of temperature and mass flow measurements are presented.
- Type:
- Dataset
- Issue Date:
- August 2018
218. Detection of an electron beam in a high density plasma via an electrostatic probe
- Author(s):
- Majeski, Stephen; Yoo, Jongsoo; Zweben, Stewart; Yamada, Masaaki
- Abstract:
- An electron beam is detected by a 1D floating potential probe array in a relatively high density (10e12 − 10e13 cm−3) and low temperature (∼ 5 eV) plasma of the Magnetic Reconnection Experiment (MRX). Clear perturbations in the floating potential profile by the electron beam are observed. Based on the floating potential profile and a current balance equation to the probe array tips, the effective width of the electron beam is determined, from which we determine the radial and toroidal beam current density profiles. After the profile of the electron beam is specified from the measured beam current, we demonstrate the consistency of the current balance equation and the location of the perturbation is also in agreement with field line mapping. No significant broadening of the electron beam is observed after the beam propagates for tens of centimeters through the high density plasma. These results prove that the field line mapping is, in principle, possible in high density plasmas.
- Type:
- Dataset
- Issue Date:
- 2018
219. ELM frequency enhancement and discharge modification through lithium granule injection into EAST H-modes
- Author(s):
- Lunsford; Hsu, J.S.; Sun, Z.; Maingi, R.; Mansfield, D.K.; Xu, W.; Zuo, G.Z.; Huang, M.; Diallo, A.; Osborne, T.; Tritz, K.; Canik, J.; Meng, X.C.; Gong, X.Z.; Wan, B.N.; Li, J.G.; EAST Team
- Abstract:
- The injection of impurity granules into fusion research discharges can serve as a catalyst for ELM events. For sufficiently low ELM frequencies, and granule sizes above a threshold, this can result in full control of the ELM cycle, referred to as ELM pacing. For this research, we extend the investigation to conditions where the natural ELM frequency is too high for ELM pacing to be realized. Utilizing multiple sizes of lithium granules and classifying their effects by granule size, we demonstrate that ELM mitigation through frequency multiplication can be used at ELM triggering rates that nominally make ELM pacing unrealizable. We find that above a size threshold, injected granules promptly trigger ELMs and commensurately enhance the ELM frequency . Below this threshold size, injection of an individual granule does not always lead to the prompt triggering of an ELM; however, collective ablation in the edge pedestal region does enhance the ELM frequency. Specifically, Li granules too small to individually trigger ELMs were injected into EAST H-mode discharges at frequencies up to 2.3 kHz; collectively the granules were observed to enhance the natural ELM frequency up to 620 Hz, resulting in a ~2.4x multiplication of the natural ELM frequency and a 50% decrease of the ELM size.
- Type:
- Dataset
- Issue Date:
- October 2018
220. ELM-free and inter-ELM divertor heat flux broadening induced by Edge Harmonics Oscillation in NSTX
- Author(s):
- Gan, K.; Ahn, J.-W.; Gray, T.K.; Zweben, S.J.; Fredrickson, E.D.; Scotti, F.; Maingi, R.; Park, J.-K.; Canal, G.P.; Soukhanovskii, V.A.; McLean, A.G.; Wirth, B.D.
- Abstract:
- A new n=1 dominated Edge Harmonic Oscillation (EHO) has been found in NSTX. The new EHO, rotating toroidally in the counter-current direction and the opposite direction of the neutral beam, was observed during certain inter-ELM and ELM-free periods of H-mode operation. This EHO is associated with a significant broadening of the integral heat flux width (?_int) by up to 150%, and a decrease in the divertor peak heat flux by >60%. An EHO induced filament was also observed by the gas puff imaging diagnostic. The toroidal rotating filaments could change the edge magnetic topology resulting in toroidal rotating strike point splitting and heat flux broadening. Experimental result of the counter current rotation of strike points splitting is consistent with the counter-current EHO.
- Type:
- Dataset
- Issue Date:
- December 2017
221. Effects of Axial Boundary Conductivity on a Free Stewartson-Shercliff Layer
- Author(s):
- Caspary, Kyle J.; Choi, Dahan; Ebrahimi, Fatima; Gilson, Erik P.; Goodman, Jeremy; Ji, Hantao
- Abstract:
- The effects of axial boundary conductivity on the formation and stability of a magnetized free Stewartson-Shercliff layer (SSL) in a short Taylor-Couette device are reported. As the axial field increases with insulating endcaps, hydrodynamic Kelvin-Helmholtz-type instabilities set in at the SSLs of the conducting fluid, resulting in a much reduced flow shear. With conducting endcaps, SSLs respond to an axial field weaker by the square root of the conductivity ratio of endcaps to fluid. Flow shear continuously builds up as the axial field increases despite the local violation of the Rayleigh criterion, leading to a large number of hydrodynamically unstable modes. Numerical simulations of both the mean flow and the instabilities are in agreement with the experimental results.
- Type:
- Dataset
- Issue Date:
- 2018
222. Electromagnetic Particle Injector for Fast Time Response Disruption Mitigation in Tokamaks
- Author(s):
- Raman, R.; Lay, W.-S.; Jarboe, T.R.; Menard, J.E.; Ono, M.
- Abstract:
- A novel, rapid time-response, disruption mitigation system referred to as the Electromagnetic Particle Injector (EPI) is described. This method can accurately deliver the radiative payload to the plasma center on a <10 ms time scale, much faster, and deeper, than what can be achieved using conventional methods. The EPI system accelerates a sabot electromagnetically. The sabot is a metallic capsule that can be accelerated to desired velocities by an electromagnetic impeller. At the end of its acceleration, within 2 ms, the sabot will release a radiative payload, which is composed of low-z granules, or a shell pellet containing smaller pellets. The primary advantage of the EPI concept over gas propelled systems is its potential to meet short warning time scales, while accurately delivering the required particle size and materials at the velocities needed for achieving the required penetration depth in high power ITER-scale discharges for thermal and runaway current disruption mitigation. The present experimental tests from a prototype system have demonstrated the acceleration of a 3.2 g sabot to over 150 m/s within 1.5 ms, consistent with the calculations, giving some degree of confidence that larger ITER-scale injector can be developed.
- Type:
- Dataset
- Issue Date:
- November 2018
223. Elemental and topographical imaging of microscopic variations in deposition on NSTX-U and DIII-D samples
- Author(s):
- Skinner, C.H.; Chrobak, C.P.; Kaita, R.; Koel, B.E.
- Abstract:
- Tokamak plasma facing components have surface roughness that can cause microscopic spatial variations in erosion and deposition and hence influence material migration, erosion lifetime, dust and tritium accumulation, and plasma contamination. However high spatial resolution measurements of deposition on the scale of the surface roughness have been lacking to date. We will present elemental images of graphite samples from NSTX-U and DIII-D DiMES experiments performed with a Scanning Auger Microprobe at sub-micron resolution that show strong microscopic variations in deposition and correlate this with 3D topographical maps of surface irregularities. The NSTX-U samples were boronized and exposed to deuterium plasmas and the DiMES samples had localized Al and W films and were exposed to dedicated helium plasmas. Topographical maps of the samples were performed with a 3D confocal optical microscope and compared to the elemental deposition pattern. The results revealed localized deposition concentrated in areas shadowed from the ion flux, incident in a direction calculated (for the DiMES case) by taking account of the magnetic pre-sheath.
- Type:
- Dataset
- Issue Date:
- October 2018
224. Experimental demonstration of hydraulic jump control in liquid metal channel flow using Lorentz force
- Author(s):
- Fisher, Adam; Kolemen, Egemen; Hvasta, Mike
- Abstract:
- In this paper, hydraulic jump control using electromagnetic force in a liquid metal flow is presented. The control methods used give insight into the hydraulic jump behavior in the presence of magnetic fields and electrical currents. Flowing liquid metals is a proposed solution to heat flux challenges posed in fusion reactors, specifically the tokamak. Unfortunately, thin, fast-flowing liquid metal divertor concepts for fusion reactors are susceptible to hydraulic jumps that drastically reduce the liquid metal flow speed, leading to potential problems such as excessive evaporation, unsteady power removal, and possible plasma disruption. Highly electrically conductive flows within the magnetic fields do not exhibit traditional hydraulic jump behavior. There is very little research investigating the use of externally injected electrical currents and magnetic fields to control liquid metal hydraulic jumps. By using externally injected electrical currents and a magnetic field, a Lorentz force (also referred to as j × B force) may be generated to control the liquid metal jump behavior. In this work, a free-surface liquid metal—GaInSn eutectic or “galinstan”—flow through an electrically insulating rectangular duct was investigated. It was shown that applying a Lorentz force has a repeatable and predictable impact on the hydraulic jump, which can be used for liquid metal control within next-generation fusion reactors.
- Type:
- Dataset
- Issue Date:
- 2018
225. Fast animal pose estimation using deep neural networks
- Author(s):
- Pereira, Talmo D.; Aldarondo, Diego E.; Willmore, Lindsay; Kislin, Mikhail; Wang, Samuel S.-H.; Murthy, Mala; Shaevitz, Joshua W.
- Abstract:
- Recent work quantifying postural dynamics has attempted to define the repertoire of behaviors performed by an animal. However, a major drawback to these techniques has been their reliance on dimensionality reduction of images which destroys information about which parts of the body are used in each behavior. To address this issue, we introduce a deep learning-based method for pose estimation, LEAP (LEAP Estimates Animal Pose). LEAP automatically predicts the positions of animal body parts using a deep convolutional neural network with as little as 10 frames of labeled data for training. This framework consists of a graphical interface for interactive labeling of body parts and software for training the network and fast prediction on new data (1 hr to train, 185 Hz predictions). We validate LEAP using videos of freely behaving fruit flies (Drosophila melanogaster) and track 32 distinct points on the body to fully describe the pose of the head, body, wings, and legs with an error rate of <3% of the animal's body length. We recapitulate a number of reported findings on insect gait dynamics and show LEAP's applicability as the first step in unsupervised behavioral classification. Finally, we extend the method to more challenging imaging situations (pairs of flies moving on a mesh-like background) and movies from freely moving mice (Mus musculus) where we track the full conformation of the head, body, and limbs.
- Type:
- Dataset
- Issue Date:
- 30 May 2018
226. Marcellus Shale Unconventional Natural Gas Well Pad Emissions
- Author(s):
- Caulton, Dana; Zondlo, Mark
- Abstract:
- Please refer to the attached README.txt file for information on the datasets
- Type:
- Dataset
- Issue Date:
- October 2018
227. Measuring shared responses across subjects using intersubject correlation
- Author(s):
- Nastase, Samuel; Gazzola, Valeria; Hasson, Uri; Keysers, Christian
- Type:
- Dataset
- Issue Date:
- 1 January 2019
228. Modeling of a Laser-Induced Rydberg Spectroscopy diagnostic for Direct Measurement of the Local Electric Field in the Edge Region of NSTX/NSTX-U
- Author(s):
- Reymond, L.; Diallo, A.; Vekselman, V.
- Abstract:
- We discuss a novel diagnostic allowing direct measurements of the local electric field in the edge region in NSTX/NSTX-U. This laser based diagnostic's principle consists of depleting the naturally populated $n=3$ level to a Rydberg state --sensitive to electric fields-- that will result in a suppression of part of the $D_{\alpha}$ emission. We refer to this approach as Laser-Induced Rydberg Spectroscopy (LIRyS). It is shown that the local electric field can be measured through the Stark induced resonances observed as dips in the $D_\alpha$ emission. Using forward-modeling of simulated absorption spectra, we show precisions reaching \SI{\pm 2}{\kilo\volt\per\meter} in regions with a local electric field of \SI{15}{\kilo\volt\per\meter}.
- Type:
- Dataset
- Issue Date:
- July 2018
229. On the scattering correction of fast-ion D-alpha signal on NSTX-U
- Author(s):
- Hao, G.Z; Heidbrink, W.W.; Liu, D.; Stagner, L.; Podesta, M.; Bortolon, A.
- Abstract:
- Analysis of fast-ion D-alpha (FIDA) data on National Spherical Torus Experiment-Upgrade (NSTX-U) shows that the cold Dα line contaminates the FIDA baseline. The scattered light is comparable to the FIDA emission. A scattering correction is required to extract the FIDA signal. Two methods that relate the scattered light contamination to the intensity of the cold Dα line are employed. One method uses laboratory measurements with a calibration lamp; the other method uses data acquired during plasma operation and singular value decomposition analysis. After correction, both the FIDA spectra and spatial profile are in better agreement with theoretical predictions.
- Type:
- Dataset
- Issue Date:
- June 2018
230. Plasma boundary shape control and real-time equilibrium reconstruction on NSTX-U
- Author(s):
- Boyer, M.; Battaglia, D.; Mueller, D.; Eidietis, N.; Erickson, K.; Ferron, J.; Gates, D.; Gerhardt, S.; Johnson, R.; Kolemen, E.; Menard, J.; Myers, C.; Sabbagh, S.; Scotti, F.; Vail, P.
- Abstract:
- The upgrade to the National Spherical Torus eXperiment (NSTX-U) included two main improvements: a larger center-stack, enabling higher toroidal field and longer pulse duration, and the addition of three new tangentially aimed neutral beam sources, which increase available heating and current drive, and allow for flexibility in shaping power, torque, current, and particle deposition profiles. To best use these new capabilities and meet the high-performance operational goals of NSTX-U, major upgrades to the NSTX-U Control System (NCS) hardware and software have been made. Several control algorithms, including those used for real-time equilibrium reconstruction and shape control, have been upgraded to improve and extend plasma control capabilities. As part of the commissioning phase of first plasma operations, the shape control system was tuned to control the boundary in both inner-wall limited and diverted discharges. It has been used to accurately track the requested evolution of the boundary (including the size of the inner gap between the plasma and central solenoid, which is a challenge for the ST configuration), X-point locations, and strike point locations, enabling repeatable discharge evolutions for scenario development and diagnostic commissioning.
- Type:
- Dataset
- Issue Date:
- March 2018
231. Quantitative imaging of carbon dimer precursor for nanomaterial synthesis in the carbon arc
- Author(s):
- Vekselman, V.; Khrabry, A.; Kaganovich, I.; Stratton, B.; Selinsky, R. S.; Raitses, Y.
- Abstract:
- Delineating the dominant processes responsible for nanomaterial synthesis in a plasma environment requires measurements of the precursor species contributing to the growth of nanostructures. We performed comprehensive measurements of spatial and temporal profiles of carbon dimers in sub-atmospheric-pressure carbon arc by laser-induced fluorescence. Measured spatial profiles of carbon dimers coincide with the growth region of carbon nanotubes (Fang et al 2016 Carbon 107 273-80) and vary depending on the arc operation mode, which is determined by the discharge current and the ablation rate of the graphite anode. The carbon dimer density profile exhibits large spatial and time variations due to motion of the arc core. A comparison of the experimental data with the 2D simulation results of self-consistent arc modeling shows a good agreement. The model predicts well the main processes determining spatial profiles of carbon dimers.
- Type:
- Dataset
- Issue Date:
- January 2018
232. Reductions in Retrieval Competition Predict the Benefit of Repeated Testing
- Author(s):
- Rafidi, Nicole S; Hulbert, Justin C; Brooks, Paula P; Norman, Kenneth A
- Abstract:
- Repeated testing (as opposed to repeated study) leads to improved long-term memory retention, but the mechanism underlying this improvement remains controversial. In this work, we test the hypothesis that retrieval practice benefits subsequent recall by reducing competition from related memories. This hypothesis implies that the degree of reduction in competition between retrieval practice attempts should predict subsequent memory for the practiced items. To test this prediction, we collected electroencephalography (EEG) data across two sessions. In the first session, participants practiced selectively retrieving exemplars from superordinate semantic categories (high competition), as well as retrieving the names of the superordinate categories from exemplars (low competition). In the second session, participants repeatedly studied and were then tested on Swahili-English vocabulary. One week after session two, participants were again tested on the vocabulary. We trained a within-subject classifier on the data from session one to distinguish high and low competition states. We then used this classifier to measure competition across multiple retrieval practice attempts in the second session. The degree to which competition decreased for a given vocabulary word predicted whether that item was subsequently remembered in the third session. These results are consistent with the hypothesis that repeated testing improves retention by reducing competition.
- Type:
- Dataset
- Issue Date:
- April 2018
233. Regarding the optimization of O1-mode ECRH and the feasibility of EBW startup on NSTX-U
- Author(s):
- Lopez, N; Poli, F
- Abstract:
- Recently published scenarios for fully non-inductive startup and operation on the National Spherical Torus eXperiment Upgrade (NSTX-U) (Menard et al 2012 Nucl. Fusion 52 083015) show Electron Cyclotron Resonance Heating (ECRH) as an important component in preparing a target plasma for efficient High Harmonic Fast Wave and Neutral Beam heating. The modeling of the propagation and absorption of EC waves in the evolving plasma is required to define the most effective window of operation, and to optimize the launcher geometry for maximal heating and current drive during this window. Here, we extend a previous optimization of O1-mode ECRH on NSTX-U to account for the full time-dependent performance of the ECRH using simulations performed with TRANSP. We find that the evolution of the density profile has a prominent role in the optimization by defining the time window of operation, which in certain cases may be a more important metric to compare launcher performance than the average power absorption. This feature cannot be captured by analysis on static profiles, and should be accounted for when optimizing ECRH on any device that operates near the cutoff density. Additionally, the utility of the electron Bernstein wave (EBW) in driving current and generating closed flux surfaces in the early startup phase has been demonstrated on a number of devices. Using standalone GENRAY simulations, we find that efficient EBW current drive is possible on NSTX-U if the injection angle is shifted below the midplane and aimed towards the top half of the vacuum vessel. However, collisional damping of the EBW is projected to be significant, in some cases accounting for up to 97% of the absorbed EBW power
- Type:
- Dataset
- Issue Date:
- June 2018
234. Regional hydroclimatic variability due to contemporary deforestation in southern Amazonia and associated boundary layer characteristics
- Author(s):
- Khanna, Jaya; Medvigy, David; Fisch, Gilberto; Neves, Theomar Trindade de Araújo Tiburtino
- Abstract:
- Amazonian deforestation causes systematic changes in regional dry season precipitation. Some of these changes at contemporary large scales (a few hundreds of kilometers) of deforestation have been associated with a ‘dynamical mesoscale circulation’, induced by the replacement of rough forest with smooth pasture. In terms of decadal averages, this dynamical mechanism yields increased precipitation in downwind regions and decreased precipitation in upwind regions of deforested areas. Daily, seasonal, and interannual variations in this phenomenon may exist, but have not yet been identified or explained. This study uses observations and numerical simulations to develop relationships between the dynamical mechanism and the local- and continental-scale atmospheric conditions across a range of time scales. It is found that the strength of the dynamical mechanism is primarily controlled by the regional-scale thermal and dynamical conditions of the boundary layer, and not by the continental- and global-scale atmospheric state. Lifting condensation level and wind speed within the boundary layer have large and positive correlations with the strength of the dynamical mechanism. The strength of these relationships depends on time scale and is strongest over the seasonal cycle. Overall, the dynamical mechanism is found to be strongest during times when the atmosphere is relatively stable. Hence, for contemporary large scales of deforestation this phenomenon is found to be the prevalent convective triggering mechanism during the dry and parts of transition seasons (especially during the dry-to-wet transition), significantly affecting the hydroclimate during this period.
- Type:
- Dataset and Software
- Issue Date:
- 2018
235. Regulation of Harvester Ant Foraging as a Closed-Loop Excitable System
- Abstract:
- Ant colonies regulate activity in response to changing conditions without using centralized control. Harvester ant colonies forage in the desert for seeds, and their regulation of foraging manages a tradeoff between spending and obtaining water. Foragers lose water while outside in the dry air, but the colony obtains water by metabolizing the fats in the seeds they eat. Previous work shows that the rate at which an outgoing forager leaves the nest depends on its recent experience of brief antennal contact with returning foragers that carry a seed. We examine how this process can yield foraging rates that are robust to uncertainty and responsive to temperature and humidity across minutes to hour-long timescales. To explore possible mechanisms, we develop a low-dimensional analytical model with a small number of parameters that captures observed foraging behavior. The model uses excitability dynamics to represent response to interactions inside the nest and a random delay distribution to represent foraging time outside the nest. We show how feedback of outgoing foragers returning to the nest stabilizes the incoming and outgoing foraging rates to a common value determined by the ``volatility’’ of available foragers. The model exhibits a critical volatility above which there is sustained foraging at a constant rate and below which there is cessation of foraging. To explain how the foraging rates of colonies adjust to temperature and humidity, we propose a mechanism that relies on foragers modifying their volatility after they leave the nest and get exposed to the environment. Our study highlights the importance of feedback in the regulation of foraging activity and points to modulation of volatility as a key to explaining differences in foraging activity in response to conditions and across colonies. Our results present opportunities for generalization to other contexts and systems with excitability and feedback across multiple timescales.
- Type:
- collection and Dataset
236. Scenario Development During Commissioning Operations on the National Spherical Torus Experiment Upgrade
- Author(s):
- Battaglia, D.J.; Boyer, M.D.; Gerhardt, S.; Mueller, D.; Myers, C.E.; Guttenfelder, W.; Menard, J.E.; Sabbagh, S.A.; Scotti, F.; Bedoya, F.; Bell, R.E.; Berkery, J.W.; Diallo, A.; Ferraro, N.; Jaworski, M.A.; Kaye, S.M.; LeBlanc, B.P.; Ono, M.; Park, J.-K.; Podesta, M.; Raman, R.; Soukhanovskii, V.A.
- Abstract:
- The National Spherical Torus Experiment Upgrade (NSTX-U) will advance the physics basis required for achieving steady-state, high-beta, and high-confinement conditions in a tokamak by accessing high toroidal field (1 T) and plasma current (1.0 - 2.0 MA) in a low aspect ratio geometry (A = 1.6 - 1.8) with flexible auxiliary heating systems (12 MW NBI, 6 MW HHFW). This paper describes progress in the development of L- and H-mode discharge scenarios and the commissioning of operational tools in the first ten weeks of operation that enable the scientific mission of NSTX-U. Vacuum field calculations completed prior to operations supported the rapid development and optimization of inductive breakdown at different values of ohmic solenoid current. The toroidal magnetic field (B_T0 = 0.65 T) exceeded the maximum values achieved on NSTX and novel long-pulse L-mode discharges with regular sawtooth activity exceeded the longest pulses produced on NSTX (tpulse > 1.8s). The increased flux of the central solenoid facilitated the development of stationary L-mode discharges over a range of density and plasma current (Ip). H-mode discharges achieved similar levels of stored energy, confinement (H98y,2 > 1) and stability (beta_N/beta_N-nowall > 1) compared to NSTX discharges for Ip < 1 MA. High-performance H-mode scenarios require an L-H transition early in the Ip ramp-up phase in order to obtain low internal inductance (li) throughout the discharge, which is conducive to maintaining vertical stability at high elongation (kappa > 2.2) and achieving long periods of MHD quiescent operations. The rapid progress in developing L- and H-mode scenarios in support of the scientific program was enabled by advances in real-time plasma control, efficient error field identification and correction, effective conditioning of the graphite wall and excellent diagnostic availability.
- Type:
- Dataset
- Issue Date:
- April 2018
237. Two-dimensional full-wave simulations of waves in space and tokamak plasmas
- Author(s):
- Kim, E.-W.; Bertelli, N.; Johnson, J.R.; Valeo, E.; Hosea, J.; Perkins, R.
- Abstract:
- We illustrate the capabilities of a recently developed two-dimensional full wave code (FW2D) in space and tokamak plasmas by adopting various values of density, magnetic field configuration and strength as well as boundary shape. As example, we first showed fast compressional wave propagation in the inner magnetosphere is dramatically modified by a plasmaspheric plume at Earth's magnetosphere. The results show that wave energy is trapped in the plume showing a leaky eigenmode-like structure with plume, which is similar to the detected magnetosonic waves. We also performed simulations of high harmonic fast waves in the scrape-off layer (SOL) plasmas of the National Spherical Torus eXperiment (NSTX)/NSTX-Upgrade. Comparison the results with previous full-wave simulations show that although the FW2D code uses a cold plasma approximation, the electric field and the fraction of the power losses in the SOL plasmas show excellent consistency and agreement with the previous full wave simulations performed by the AORSA code.
- Type:
- Dataset
- Issue Date:
- October 2018
238. Whistler wave generation by anisotropic tail electrons during asymmetric magnetic reconnection in space and laboratory
- Author(s):
- Yoo, Jongsoo; Jara-almonte, J.; Yerger, Evan; Wang, Shan; Qian, Tony; Le, Ari; Ji, Hantao; Yamada, Masaaki; Fox, William; Kim, Eun-Hwa; Chen, Li-Jen; Gershman, Daniel
- Abstract:
- Whistler wave generation near the magnetospheric separatrix during reconnection at the dayside magnetopause is studied with data from the Magnetospheric Multiscale (MMS) mission. The dispersion relation of the whistler mode is measured for the first time near the reconnection region in space, which shows that whistler waves propagate nearly parallel to the magnetic field line. A linear analysis indicates that the whistler waves are generated by temperature anisotropy in the electron tail population. This is caused by loss of electrons with a high velocity parallel to the magnetic field to the exhaust region. There is a positive correlation between activities of whistler waves and the lower-hybrid drift instability (LHDI) both in laboratory and space, indicating the enhanced transport by LHDI may be responsible for the loss of electrons with a high parallel velocity.
- Type:
- Dataset
- Issue Date:
- August 2018
239. A Reduced Resistive Wall Mode Kinetic Stability Model for Disruption Forecasting
- Author(s):
- Berkery, J.W.; Sabbagh, S.A.; Bell, R.E.; Gerhardt, S.P.; LeBlanc, B.P.
- Abstract:
- Kinetic modification of ideal stability theory from stabilizing resonances of mode-particle interaction has had success in explaining resistive wall mode (RWM) stability limits in tokamaks. With the goal of real-time stability forecasting, a reduced kinetic stability model has been implemented in the new Disruption Event Characterization and Forecasting (DECAF) code, which has been written to analyze disruptions in tokamaks. The reduced model incorporates parameterized models for ideal limits on beta, a ratio of plasma pressure to magnetic pressure, which are shown to be in good agreement with DCON code calculations. Increased beta between these ideal limits causes a shift in the unstable region of delta W_K space, where delta W_K is the change in potential energy due to kinetic effects that is solved for by the reduced model, such that it is possible for plasmas to be unstable at intermediate beta but stable at higher beta. Gaussian functions for delta W_K are defined as functions of E cross B frequency and collisionality, with parameters reflecting the experience of the National Spherical Torus Experiment (NSTX). The reduced model was tested on a database of discharges from NSTX and experimentally stable and unstable discharges were separated noticeably on a stability map in E cross B frequency, collisionality space. The reduced model only failed to predict an unstable RWM in 15.6% of cases with an experimentally unstable RWM and performed well on predicting stability for experimentally stable discharges as well.
- Type:
- Dataset
- Issue Date:
- May 2017
240. A Riccati Solution for the Ideal MHD Plasma Response with Applications to Real-time Stability Control
- Author(s):
- Glasser, A.; Kolemen, E.; Glasser, A.H.
- Abstract:
- To effectuate near real-time feedback control of ideal MHD instabilities in a tokamak geometry, a rapid solution for stability analysis is a prerequisite. Toward this end, we reformulate the δW stability method with a Hamilton-Jacobi theory, elucidating analytical and numerical features of the generic tokamak ideal MHD stability problem. The plasma response matrix is demonstrated to be the solution of an ideal MHD matrix Riccati differential equation (MRDE). Since Riccati equations are prevalent in the control theory literature, such a shift in perspective brings to bear a range of numerical methods that are well-suited to the robust, fast solution of control problems. We discuss the usefulness of Riccati techniques in solving the stiff ODEs often encountered in ideal MHD stability analyses-—for example, in tokamak edge and stellarator physics. We then demonstrate the applicability of such methods to an existing 2D ideal MHD stability code—DCON—enabling its parallel operation in near real-time. Output is shown to match with high accuracy, and with wall-clock time ≪ 1s. Such speed may help enable active feedback ideal MHD stability control, especially in tokamak plasmas whose ideal MHD equilibria evolve with inductive timescale τ > 1s-—as in ITER.
- Type:
- Dataset
- Issue Date:
- March 2018
241. Advances in boronization on NSTX-Upgrade
- Author(s):
- Skinner, C.H.; Bedoya, F.; Scotti, F.; Allain, J.P.; Blanchard, W.; Cai, D.; Jaworski, M.; Koel, B.E.
- Abstract:
- Boronization has been effective in reducing plasma impurities and enabling access to higher density, higher confinement plasmas in many magnetic fusion devices. The National Spherical Torus eXperiment, NSTX, has recently undergone a major upgrade to NSTX-U in order to develop the physics basis for a ST-based Fusion Nuclear Science Facility (FNSF) with capability for double the toroidal field, plasma current, and NBI heating power and increased pulse duration from 1–1.5 s to 5–8 s. A new deuterated tri-methyl boron conditioning system was implemented together with a novel surface analysis diagnostic. We report on the spatial distribution of the boron deposition versus discharge pressure, gas injection and electrode location. The oxygen concentration of the plasma facing surface was measured by in-vacuo XPS and increased both with plasma exposure and with exposure to trace residual gases. This increase correlated with the rise of oxygen emission from the plasma.
- Type:
- Dataset
- Issue Date:
- January 2017
242. Amplification of local changes along the timescale processing hierarchy
- Author(s):
- Yeshurun, Yaara; Nguyen, Mai; Hasson, Uri
- Abstract:
- Small changes in word choice can lead to dramatically different interpretations of narratives. How does the brain accumulate and integrate such local changes to construct unique neural representations for different stories? In this study we created two distinct narratives by changing only a few words in each sentence (e.g. “he” to “she” or “sobbing” to “laughing”) while preserving the grammatical structure across stories. We then measured changes in neural responses between the two stories. We found that the differences in neural responses between the two stories gradually increased along the hierarchy of processing timescales. For areas with short integration windows, such as early auditory cortex, the differences in neural responses between the two stories were relatively small. In contrast, in areas with the longest integration windows at the top of the hierarchy, such as the precuneus, temporal parietal junction, and medial frontal cortices, there were large differences in neural responses between stories. Furthermore, this gradual increase in neural difference between the stories was highly correlated with an area’s ability to integrate information over time. Amplification of neural differences did not occur when changes in words did not alter the interpretation of the story (e.g. “sobbing” to “crying”). Our results demonstrate how subtle differences in words are gradually accumulated and amplified along the cortical hierarchy as the brain constructs a narrative over time.
- Type:
- Dataset
- Issue Date:
- August 2017
243. Application of Benchmarked Kinetic Resistive Wall Mode Stability Codes to ITER, Including Additional Physics
- Author(s):
- Berkery, J.W.; Wang, Z.R.; Sabbagh, S.A.; Liu, Y.Q.; Betti, R.; Guazotto, L.
- Abstract:
- Leading resistive wall mode (RWM) stability codes MARS-K [Y. Liu, et al., Phys. Plasmas 15, 112503 (2008)] and MISK [B. Hu, et al., Phys. Plasmas 12, 057301 (2005)] have been previously benchmarked. The benchmarking has now been extended to include additional physics, and used to project the stability of ITER in a realistic operating space. Due to ITER's relatively low plasma rotation and collisionality, collisions and non-resonance rotational effects were both found to have little impact on stability, and these non-resonance rotational effects also will not self-consistently affect the ITER RWM eigenfunction. Resonances between thermal ions and electrons and the expected level of ITER toroidal rotation were found to be important to stability, as were alpha particles, which are not in rotational resonance. MISK calculations show that without alpha particles, ITER is projected to be unstable to the RWM, but the expected level of alphas is calculated to provide a sufficient level of stability.
- Type:
- Dataset
- Issue Date:
- October 2017
244. Application of IR imaging for free-surface velocity measurement in liquid-metal systems
- Author(s):
- Hvasta, M.H.; Kolemen, E.; Fisher, A.
- Abstract:
- Measuring free-surface, liquid-metal flow velocity is challenging to do in a reliable and accurate manner. This paper presents a non-invasive, easily-calibrated method of measuring the surface velocities of open-channel liquid-metal flows using an IR camera. Unlike other spatially-limited methods, this IR camera particle tracking technique provides full field-of-view data that can be used to better understand open-channel flows and determine surface boundary conditions. This method could be implemented and automated for a wide range of liquid-metal experiments, even if they operate at high-temperatures or within strong magnetic fields.
- Type:
- Dataset
- Issue Date:
- January 2017
245. Application of IR imaging for free-surface velocity measurement in liquid-metal systems
- Author(s):
- Hvasta, M. G.; Kolemen, E.; Fisher, A.
- Abstract:
- Measuring free-surface, liquid-metal flow velocity is challenging to do in a reliable and accurate manner. This paper presents a non-invasive, easily-calibrated method of measuring the surface velocities of open-channel liquid-metal flows using an IR camera. Unlike other spatially-limited methods, this IR camera particle tracking technique provides full field-of-view data that can be used to better understand open-channel flows and determine surface boundary conditions. This method could be implemented and automated for a wide range of liquid-metal experiments, even if they operate at high-temperatures or within strong magnetic fields.
- Type:
- Dataset
- Issue Date:
- January 2017
246. Application of Townsend avalanche theory to tokamak startup by coaxial helicity injection
- Author(s):
- Hammond, K.C.; Raman, R.; Volpe, F.A.
- Abstract:
- Townsend avalanche theory is employed to model and interpret plasma initiation in NSTX by Ohmic heating and coaxial helicity injection (CHI). The model is informed by spatially resolved vacuum calculations of electric field and magnetic field line connection length in the poloidal cross-section. The model is shown to explain observations of Ohmic startup including the duration and location of breakdown. Adapting the model to discharges initiated by CHI offers insight into the causes of upper divertor (absorber) arcs in cases where the discharge fails to initiate in the lower divertor gap. Finally, upper and lower limits are established for vessel gas fill based on requirements for breakdown and radiation. It is predicted that CHI experiments on NSTX-U should be able to use as much as four times the amount of prefill gas employed in CHI experiments in NSTX. This should provide greater flexibility for plasma start-up, as the injector flux is projected to be increased in NSTX-U.
- Type:
- Dataset
- Issue Date:
- September 2017
247. Data for Nature Climate Change article 'Regional dry-season climate changes due to three decades of Amazonian deforestation'
- Author(s):
- Khanna, Jaya; Medvigy, David; Fueglistaler, Stephan; Walko, Robert
- Abstract:
- More than 20% Amazon rainforest has been cleared in the past three decades triggering important hydroclimatic changes. Small-scale (~few kilometers) deforestation in the 1980s has caused thermally-triggered atmospheric circulations that increase regional cloudiness and precipitation frequency. However, these circulations are predicted to diminish as deforestation increases. Here we use multi-decadal satellite records and numerical model simulations to show a regime shift in the regional hydroclimate accompanying increasing deforestation in Rondônia, Brazil. Compared to the 1980s, present-day deforested areas in downwind western Rondônia are found to be wetter than upwind eastern deforested areas during the local dry season. The resultant precipitation change in the two regions is approximately ±25% of the deforested area mean. Meso-resolution simulations robustly reproduce this transition when forced with increasing deforestation alone, showing a negligible role of large-scale climate variability. Furthermore, deforestation-induced surface roughness reduction is found to play an essential role in the present-day dry season hydroclimate. Our study illustrates the strong scale-sensitivity of the climatic response to Amazonian deforestation and suggests that deforestation is sufficiently advanced to have caused a shift from a thermally- to a dynamically-driven hydroclimatic regime.
- Type:
- Dataset and Software
- Issue Date:
- 2017
248. Density perturbation mode structure of high frequency compressional and global Alfvén eigenmodes in the National Spherical Torus Experiment using a novel reflectometer analysis technique
- Author(s):
- Crocker, N.A.; Kubota, S.; Peebles, W.A.; Rhodes, T.L.; Fredrickson, E.D.; Belova, E.; Diallo, A.; LeBlanc, B.P.; Sabbagh, S.A.
- Abstract:
- Reflectometry measurements of compressional (CAE) and global (GAE) Alfvén eigenmodes are analyzed to obtain the amplitude and spatial structure of the density perturbations associated with the modes. A novel analysis technique developed for this purpose is presented. The analysis also naturally yields the amplitude and spatial structure of the density contour radial displacement, which is found to be 2–4 times larger than the value estimated directly from the reflectometer measurements using the much simpler ‘mirror approximation’. The modes were driven by beam ions in a high power (6 MW) neutral beam heated H-mode discharge (#141398) in the National Spherical Torus Experiment. The results of the analysis are used to assess the contribution of the modes to core energy transport and ion heating. The total displacement amplitude of the modes, which is shown to be larger than previously estimated (Crocker et al 2013 Nucl. Fusion 53 43017), is compared to the predicted threshold (Gorelenkov et al 2010 Nucl. Fusion 50 84012) for the anomalously high heat diffusion inferred from transport modeling in similar NSTX discharges. The results of the analysis also have strong implications for the energy transport via coupling of CAEs to kinetic Alfvén waves seen in simulations with the Hybrid MHD code (Belova et al 2015 Phys. Rev. Lett. 115 15001). Finally, the amplitudes of the observed CAEs fall well below the threshold for causing significant ion heating by stochastic velocity space diffusion (Gates et al 2001 Phys. Rev. Lett. 87 205003).
- Type:
- Dataset
- Issue Date:
- November 2017
249. Design of Faraday cup ion detectors built by thin film deposition
- Author(s):
- Szalkowski, G.A.; Darrow, D.S.; Cecil, F.E.
- Abstract:
- Thin film Faraday cup detectors can provide measurements of fast ion loss from magnetically confined fusion plasmas. These multilayer detectors can resolve the energy distribution of the lost ions in addition to giving the total loss rate. Prior detectors were assembled from discrete foils and insulating sheets. Outlined here is a design methodology for creating detectors using thin film deposition that are suited to particular scientific goals. The intention is to use detectors created by this method on JET and NSTX-U. The detectors will consist of alternating layers of aluminum and silicon dioxide, with layer thicknesses chosen to isolate energies of interest. Thin film deposition offers the advantage of relatively simple and more mechanically robust construction compared to other methods, as well as allowing precise control of film thickness. Furthermore, this depositional fabrication technique places the layers in intimate thermal contact, providing for three-dimensional conduction and dissipation of the ion-produced heating in the layers, rather than the essentially two-dimensional heat conduction in the discrete foil stack implementation.
- Type:
- Dataset
- Issue Date:
- January 2017
250. Drift kinetic effects on the plasma response in high beta spherical tokamak experiments
- Author(s):
- Wang, Z.R.; Park, J.-K.; Menard, J.E.; Liu, Y.Q.; Kaye, S.M.; Gerhardt, S.
- Abstract:
- High $\beta$ plasma response to the rotating n=1 external magnetic perturbations is numerically studied and compared with National Spherical Torus eXperiment (NSTX). The hybrid magnetohydrodynamic(MHD)-kinetic modeling shows the drift kinetic effects are important to resolve the disagreement of plasma response between the ideal MHD prediction and the NSTX experimental observation when plasma pressure reaches and exceeds the no-wall limit [F. Troyon et al., Plasma Phys. Control. Fusion \textbf{26}, 209 (1984)]. Since the external rotating fields and high plasma rotation are presented in NSTX experiments, the importance of resistive wall effect and plasma rotation on determining the plasma response is also identified, where the resistive wall suppresses the plasma response through the wall eddy current. The inertial energy, due to plasma rotation, destabilizes the plasma. The complexity of plasma response, in this study, indicates that MHD modeling, including comprehensive physics e.g. the drift kinetic effects, resistive wall and plasma rotation, is essential to reliably predict the plasma behavior in high beta spherical tokamak device.
- Type:
- Dataset
- Issue Date:
- September 2017