Search

Start Over Year Published 2018

1. Blob-hole correlation model for edge turbulence and comparisons with NSTX GPI data

Author(s):
Myra, J.R.; Zweben, S.J.; Russell, D.A.
Abstract:
Gas puff imaging (GPI) observations made in NSTX [Zweben S J, et al., 2017 Phys. Plasmas 24 102509] have revealed two-point spatial correlations of edge and scrape-off layer turbulence in the plane perpendicular to the magnetic field. A common feature is the occurrence of dipole-like patterns with significant regions of negative correlation. In this paper, we explore the possibility that these dipole patterns may be due to blob-hole pairs. Statistical methods are applied to determine the two-point spatial correlation that results from a model of blob-hole pair formation. It is shown that the model produces dipole correlation patterns that are qualitatively similar to the GPI data in several respects. Effects of the reference location (confined surfaces or scrape-off layer), a superimposed random background, hole velocity and lifetime, and background sheared flows are explored and discussed with respect to experimental observations. Additional analysis of the experimental GPI dataset is performed to further test this blob-hole correlation model. A time delay two-point spatial correlation study did not reveal inward propagation of the negative correlation structures that were postulated to correspond to holes in the data nor did it suggest that the negative correlation structures are due to neutral shadowing. However, tracing of the highest and lowest values (extrema) of the normalized GPI fluctuations shows strong evidence for mean inward propagation of minima and outward propagation of maxima, in qualitative agreement with theoretical expectations. Other properties of the experimentally observed extrema are discussed.
Type:
Dataset
Issue Date:
July 2018

2. Calibrationless rotating Lorentz-force flowmeters for low flow rate applications

Author(s):
Hvasta, M. G.; Dudt, D.; Fisher, A. E.; Kolemen, E.
Abstract:
A 'weighted magnetic bearing' has been developed to improve the performance of rotating Lorentz-force flowmeters (RLFFs). Experiments have shown that the new bearing reduces frictional losses within a double-sided, disc-style RLFF to negligible levels. Operating such an RLFF under 'frictionless' conditions provides two major benefits. First, the steady-state velocity of the RLFF magnets matches the average velocity of the flowing liquid at low flow rates. This enables an RLFF to make accurate volumetric flow measurements without any calibration or prior knowledge of the fluid properties. Second, due to minimized frictional losses, an RLFF is able to measure low flow rates that cannot be detected when conventional, high-friction bearings are used. This paper provides a brief background on RLFFs, gives a detailed description of weighted magnetic bearings, and compares experimental RLFF data to measurements taken with a commercially available flowmeter.
Type:
Dataset
Issue Date:
29 May 2018

3. Collapse of reacted fracture surface decreases permeability and frictional strength

Author(s):
Peters, Catherine A.; Spokas, Kasparas
Abstract:
Geochemical and geomechanical perturbations of the subsurface caused by the injection of fluids present the risk of leakage and seismicity. This study investigated how flow of acidic fluids affects hydraulic and frictional properties of fractures using experiments with 3.8 cm-long specimens of Eagle Ford shale, a laminated shale with carbonate-rich strata. In low-pressure flow cells, one set of samples was exposed to an acidic brine and another set was exposed to a neutral brine. X-ray computed tomography and x-ray fluorescence analysis revealed that samples exposed to the acidic brine were calcite-depleted and had developed a porous altered layer, while the other set showed little evidence of alteration. After reaction, samples were compacted and sheared in a triaxial cell that supplied normal stress and differential pore pressure at prescribed sliding velocities, independently measuring friction and permeability. During the initial compaction, the porous altered layer collapsed into fine particles that filled the fracture aperture. This effectively impeded flow and sealed the fracture, resulting in a decrease in fracture permeability by 1 to 2 orders of magnitude relative to the compressed unaltered fractures. During shear, the collapsed layer of fine-grained particles prevented the formation of interlocking micro-asperities resulting in lower frictional strength. With regard to subsurface risks, this study showcases how coupled geochemical and geomechanical processes could favorably seal fractures to inhibit leakage, but also could increase the likelihood of induced seismicity. These findings have important implications for geological carbon sequestration, pressurized fluid energy storage, geothermal energy, and other subsurface technologies.
Type:
Dataset
Issue Date:
2018

4. Compact steady-state tokamak performance dependence on magnet and core physics limits

Author(s):
Menard, J.E.
Abstract:
Compact tokamak fusion reactors utilizing advanced high-temperature superconducting magnets for the toroidal field coils have received considerable recent attention due to the promise of more compact devices and more economical fusion energy development. Facilities with combined Fusion Nuclear Science (FNS) and Pilot Plant missions to provide both the nuclear environment needed to develop fusion materials and components while also potentially achieving sufficient fusion performance to generate modest net electrical power are considered. The performance of the tokamak fusion system is assessed using a range of core physics and toroidal field magnet performance constraints to better understand which parameters most strongly influence the achievable fusion performance.
Type:
Dataset
Issue Date:
December 2018

5. Demonstrating electromagnetic control of free-surface, liquid-metal flows relevant to fusion reactors

Author(s):
Hvasta, M. G.; Kolemen, E.; Fisher, A. E.; Ji, H.
Abstract:
Plasma-facing components (PFC's) made from solid materials may not be able to withstand the large heat and particle fluxes that will be produced within next-generation fusion reactors. To address the shortcomings of solid PFC's, a variety of liquid-metal (LM) PFC concepts have been proposed. Many of the suggested LM-PFC designs rely on electromagnetic restraint (Lorentz force) to keep free-surface, liquid-metal flows adhered to the interior surfaces of a fusion reactor. However, there is very little, if any, experimental data demonstrating that free-surface, LM-PFC's can actually be electromagnetically controlled. Therefore, in this study, electrical currents were injected into a free-surface liquid-metal that was flowing through a uniform magnetic field. The resultant Lorentz force generated within the liquid-metal affected the velocity and depth of the flow in a controllable manner that closely matched theoretical predictions. These results show the promise of electromagnetic control for LM-PFC's and suggest that electromagnetic control could be further developed to adjust liquid-metal nozzle output, prevent splashing within a tokamak, and alter heat transfer properties for a wide-range of liquid-metal systems.
Type:
Dataset
Issue Date:
January 2018

6. Design and measurement methods for a lithium vapor box similarity experiment

Author(s):
Schwartz, J. A.; Emdee, E. D.; Jaworski, M. A; Goldston, R. J.
Abstract:
The lithium vapor box divertor is a concept for handling the extreme divertor heat fluxes in magnetic fusion devices. In a baffled slot divertor, plasma interacts with a dense cloud of Li vapor which radiates and cools the plasma, leading to recombination and detachment. Before testing on a tokamak the concept should be validated: we plan to study detachment and heat redistribution by a Li vapor cloud in laboratory experiments. Mass changes and temperatures are measured to validate a Direct Simulation Monte Carlo model of neutral Li. The initial experiment involves a 5 cm diameter steel box containing 10g of Li held at 650 degrees C as vapor flows out a wide nozzle into a similarly-sized box at a lower temperature. Diagnosis is made challenging by the required material compatibility with lithium vapor. Vapor pressure is a steep function of temperature, so to validate mass flow models to within 10%, absolute temperature to within 4.5K is required. The apparatus is designed to be used with an analytical balance to determine mass transport. Details of the apparatus and methods of temperature and mass flow measurements are presented.
Type:
Dataset
Issue Date:
August 2018

7. Detection of an electron beam in a high density plasma via an electrostatic probe

Author(s):
Majeski, Stephen; Yoo, Jongsoo; Zweben, Stewart; Yamada, Masaaki
Abstract:
An electron beam is detected by a 1D floating potential probe array in a relatively high density (10e12 − 10e13 cm−3) and low temperature (∼ 5 eV) plasma of the Magnetic Reconnection Experiment (MRX). Clear perturbations in the floating potential profile by the electron beam are observed. Based on the floating potential profile and a current balance equation to the probe array tips, the effective width of the electron beam is determined, from which we determine the radial and toroidal beam current density profiles. After the profile of the electron beam is specified from the measured beam current, we demonstrate the consistency of the current balance equation and the location of the perturbation is also in agreement with field line mapping. No significant broadening of the electron beam is observed after the beam propagates for tens of centimeters through the high density plasma. These results prove that the field line mapping is, in principle, possible in high density plasmas.
Type:
Dataset
Issue Date:
2018

8. ELM frequency enhancement and discharge modification through lithium granule injection into EAST H-modes

Author(s):
Lunsford; Hsu, J.S.; Sun, Z.; Maingi, R.; Mansfield, D.K.; Xu, W.; Zuo, G.Z.; Huang, M.; Diallo, A.; Osborne, T.; Tritz, K.; Canik, J.; Meng, X.C.; Gong, X.Z.; Wan, B.N.; Li, J.G.; EAST Team
Abstract:
The injection of impurity granules into fusion research discharges can serve as a catalyst for ELM events. For sufficiently low ELM frequencies, and granule sizes above a threshold, this can result in full control of the ELM cycle, referred to as ELM pacing. For this research, we extend the investigation to conditions where the natural ELM frequency is too high for ELM pacing to be realized. Utilizing multiple sizes of lithium granules and classifying their effects by granule size, we demonstrate that ELM mitigation through frequency multiplication can be used at ELM triggering rates that nominally make ELM pacing unrealizable. We find that above a size threshold, injected granules promptly trigger ELMs and commensurately enhance the ELM frequency . Below this threshold size, injection of an individual granule does not always lead to the prompt triggering of an ELM; however, collective ablation in the edge pedestal region does enhance the ELM frequency. Specifically, Li granules too small to individually trigger ELMs were injected into EAST H-mode discharges at frequencies up to 2.3 kHz; collectively the granules were observed to enhance the natural ELM frequency up to 620 Hz, resulting in a ~2.4x multiplication of the natural ELM frequency and a 50% decrease of the ELM size.
Type:
Dataset
Issue Date:
October 2018

9. ELM-free and inter-ELM divertor heat flux broadening induced by Edge Harmonics Oscillation in NSTX

Author(s):
Gan, K.; Ahn, J.-W.; Gray, T.K.; Zweben, S.J.; Fredrickson, E.D.; Scotti, F.; Maingi, R.; Park, J.-K.; Canal, G.P.; Soukhanovskii, V.A.; McLean, A.G.; Wirth, B.D.
Abstract:
A new n=1 dominated Edge Harmonic Oscillation (EHO) has been found in NSTX. The new EHO, rotating toroidally in the counter-current direction and the opposite direction of the neutral beam, was observed during certain inter-ELM and ELM-free periods of H-mode operation. This EHO is associated with a significant broadening of the integral heat flux width (?_int) by up to 150%, and a decrease in the divertor peak heat flux by >60%. An EHO induced filament was also observed by the gas puff imaging diagnostic. The toroidal rotating filaments could change the edge magnetic topology resulting in toroidal rotating strike point splitting and heat flux broadening. Experimental result of the counter current rotation of strike points splitting is consistent with the counter-current EHO.
Type:
Dataset
Issue Date:
December 2017

10. Effects of Axial Boundary Conductivity on a Free Stewartson-Shercliff Layer

Author(s):
Caspary, Kyle J.; Choi, Dahan; Ebrahimi, Fatima; Gilson, Erik P.; Goodman, Jeremy; Ji, Hantao
Abstract:
The effects of axial boundary conductivity on the formation and stability of a magnetized free Stewartson-Shercliff layer (SSL) in a short Taylor-Couette device are reported. As the axial field increases with insulating endcaps, hydrodynamic Kelvin-Helmholtz-type instabilities set in at the SSLs of the conducting fluid, resulting in a much reduced flow shear. With conducting endcaps, SSLs respond to an axial field weaker by the square root of the conductivity ratio of endcaps to fluid. Flow shear continuously builds up as the axial field increases despite the local violation of the Rayleigh criterion, leading to a large number of hydrodynamically unstable modes. Numerical simulations of both the mean flow and the instabilities are in agreement with the experimental results.
Type:
Dataset
Issue Date:
2018

11. Electromagnetic Particle Injector for Fast Time Response Disruption Mitigation in Tokamaks

Author(s):
Raman, R.; Lay, W.-S.; Jarboe, T.R.; Menard, J.E.; Ono, M.
Abstract:
A novel, rapid time-response, disruption mitigation system referred to as the Electromagnetic Particle Injector (EPI) is described. This method can accurately deliver the radiative payload to the plasma center on a <10 ms time scale, much faster, and deeper, than what can be achieved using conventional methods. The EPI system accelerates a sabot electromagnetically. The sabot is a metallic capsule that can be accelerated to desired velocities by an electromagnetic impeller. At the end of its acceleration, within 2 ms, the sabot will release a radiative payload, which is composed of low-z granules, or a shell pellet containing smaller pellets. The primary advantage of the EPI concept over gas propelled systems is its potential to meet short warning time scales, while accurately delivering the required particle size and materials at the velocities needed for achieving the required penetration depth in high power ITER-scale discharges for thermal and runaway current disruption mitigation. The present experimental tests from a prototype system have demonstrated the acceleration of a 3.2 g sabot to over 150 m/s within 1.5 ms, consistent with the calculations, giving some degree of confidence that larger ITER-scale injector can be developed.
Type:
Dataset
Issue Date:
November 2018

12. Electron-density-sensitive Line Ratios of Fe XIII--XVI from Laboratory Sources Compared to CHIANTI

Author(s):
Weller, M.E.; Beiersdorfer, P.; Soukhanovskii, V.A.; Scotti, F.; LeBlanc, B.P.
Abstract:
We present electron-density-sensitive line ratios for Fe XIII–XVI measured in the spectral wavelength range of 200–440 Å and an electron density range of (1–4)×10^13 cm^−3. The results provide a test at the high-density limit of density-sensitive line ratios useful for astrophysical studies. The measurements were performed on the National Spherical Torus Experiment-Upgrade, where electron densities were measured independently by the laser Thomson scattering diagnostic. Spectra were collected with a flat-field grazing-incidence spectrometer, which provided a spectral resolution of up to 0.3 Å, i.e., high resolution across the broad wavelength range. The response of the instrument was relatively calibrated using spectroscopic techniques in order to improve accuracy. The line ratios are compared to other laboratory sources and the latest version of CHIANTI (8.0.2), and an agreement within 30% is found.
Type:
Dataset
Issue Date:
February 2018

13. Elemental and topographical imaging of microscopic variations in deposition on NSTX-U and DIII-D samples

Author(s):
Skinner, C.H.; Chrobak, C.P.; Kaita, R.; Koel, B.E.
Abstract:
Tokamak plasma facing components have surface roughness that can cause microscopic spatial variations in erosion and deposition and hence influence material migration, erosion lifetime, dust and tritium accumulation, and plasma contamination. However high spatial resolution measurements of deposition on the scale of the surface roughness have been lacking to date. We will present elemental images of graphite samples from NSTX-U and DIII-D DiMES experiments performed with a Scanning Auger Microprobe at sub-micron resolution that show strong microscopic variations in deposition and correlate this with 3D topographical maps of surface irregularities. The NSTX-U samples were boronized and exposed to deuterium plasmas and the DiMES samples had localized Al and W films and were exposed to dedicated helium plasmas. Topographical maps of the samples were performed with a 3D confocal optical microscope and compared to the elemental deposition pattern. The results revealed localized deposition concentrated in areas shadowed from the ion flux, incident in a direction calculated (for the DiMES case) by taking account of the magnetic pre-sheath.
Type:
Dataset
Issue Date:
October 2018

14. Experimental demonstration of hydraulic jump control in liquid metal channel flow using Lorentz force

Author(s):
Fisher, Adam; Kolemen, Egemen; Hvasta, Mike
Abstract:
In this paper, hydraulic jump control using electromagnetic force in a liquid metal flow is presented. The control methods used give insight into the hydraulic jump behavior in the presence of magnetic fields and electrical currents. Flowing liquid metals is a proposed solution to heat flux challenges posed in fusion reactors, specifically the tokamak. Unfortunately, thin, fast-flowing liquid metal divertor concepts for fusion reactors are susceptible to hydraulic jumps that drastically reduce the liquid metal flow speed, leading to potential problems such as excessive evaporation, unsteady power removal, and possible plasma disruption. Highly electrically conductive flows within the magnetic fields do not exhibit traditional hydraulic jump behavior. There is very little research investigating the use of externally injected electrical currents and magnetic fields to control liquid metal hydraulic jumps. By using externally injected electrical currents and a magnetic field, a Lorentz force (also referred to as j × B force) may be generated to control the liquid metal jump behavior. In this work, a free-surface liquid metal—GaInSn eutectic or “galinstan”—flow through an electrically insulating rectangular duct was investigated. It was shown that applying a Lorentz force has a repeatable and predictable impact on the hydraulic jump, which can be used for liquid metal control within next-generation fusion reactors.
Type:
Dataset
Issue Date:
2018

15. Fast animal pose estimation using deep neural networks

Author(s):
Pereira, Talmo D.; Aldarondo, Diego E.; Willmore, Lindsay; Kislin, Mikhail; Wang, Samuel S.-H.; Murthy, Mala; Shaevitz, Joshua W.
Abstract:
Recent work quantifying postural dynamics has attempted to define the repertoire of behaviors performed by an animal. However, a major drawback to these techniques has been their reliance on dimensionality reduction of images which destroys information about which parts of the body are used in each behavior. To address this issue, we introduce a deep learning-based method for pose estimation, LEAP (LEAP Estimates Animal Pose). LEAP automatically predicts the positions of animal body parts using a deep convolutional neural network with as little as 10 frames of labeled data for training. This framework consists of a graphical interface for interactive labeling of body parts and software for training the network and fast prediction on new data (1 hr to train, 185 Hz predictions). We validate LEAP using videos of freely behaving fruit flies (Drosophila melanogaster) and track 32 distinct points on the body to fully describe the pose of the head, body, wings, and legs with an error rate of <3% of the animal's body length. We recapitulate a number of reported findings on insect gait dynamics and show LEAP's applicability as the first step in unsupervised behavioral classification. Finally, we extend the method to more challenging imaging situations (pairs of flies moving on a mesh-like background) and movies from freely moving mice (Mus musculus) where we track the full conformation of the head, body, and limbs.
Type:
Dataset
Issue Date:
30 May 2018

18. Modeling of a Laser-Induced Rydberg Spectroscopy diagnostic for Direct Measurement of the Local Electric Field in the Edge Region of NSTX/NSTX-U

Author(s):
Reymond, L.; Diallo, A.; Vekselman, V.
Abstract:
We discuss a novel diagnostic allowing direct measurements of the local electric field in the edge region in NSTX/NSTX-U. This laser based diagnostic's principle consists of depleting the naturally populated $n=3$ level to a Rydberg state --sensitive to electric fields-- that will result in a suppression of part of the $D_{\alpha}$ emission. We refer to this approach as Laser-Induced Rydberg Spectroscopy (LIRyS). It is shown that the local electric field can be measured through the Stark induced resonances observed as dips in the $D_\alpha$ emission. Using forward-modeling of simulated absorption spectra, we show precisions reaching \SI{\pm 2}{\kilo\volt\per\meter} in regions with a local electric field of \SI{15}{\kilo\volt\per\meter}.
Type:
Dataset
Issue Date:
July 2018

19. On the scattering correction of fast-ion D-alpha signal on NSTX-U

Author(s):
Hao, G.Z; Heidbrink, W.W.; Liu, D.; Stagner, L.; Podesta, M.; Bortolon, A.
Abstract:
Analysis of fast-ion D-alpha (FIDA) data on National Spherical Torus Experiment-Upgrade (NSTX-U) shows that the cold Dα line contaminates the FIDA baseline. The scattered light is comparable to the FIDA emission. A scattering correction is required to extract the FIDA signal. Two methods that relate the scattered light contamination to the intensity of the cold Dα line are employed. One method uses laboratory measurements with a calibration lamp; the other method uses data acquired during plasma operation and singular value decomposition analysis. After correction, both the FIDA spectra and spatial profile are in better agreement with theoretical predictions.
Type:
Dataset
Issue Date:
June 2018

20. Plasma boundary shape control and real-time equilibrium reconstruction on NSTX-U

Author(s):
Boyer, M.; Battaglia, D.; Mueller, D.; Eidietis, N.; Erickson, K.; Ferron, J.; Gates, D.; Gerhardt, S.; Johnson, R.; Kolemen, E.; Menard, J.; Myers, C.; Sabbagh, S.; Scotti, F.; Vail, P.
Abstract:
The upgrade to the National Spherical Torus eXperiment (NSTX-U) included two main improvements: a larger center-stack, enabling higher toroidal field and longer pulse duration, and the addition of three new tangentially aimed neutral beam sources, which increase available heating and current drive, and allow for flexibility in shaping power, torque, current, and particle deposition profiles. To best use these new capabilities and meet the high-performance operational goals of NSTX-U, major upgrades to the NSTX-U Control System (NCS) hardware and software have been made. Several control algorithms, including those used for real-time equilibrium reconstruction and shape control, have been upgraded to improve and extend plasma control capabilities. As part of the commissioning phase of first plasma operations, the shape control system was tuned to control the boundary in both inner-wall limited and diverted discharges. It has been used to accurately track the requested evolution of the boundary (including the size of the inner gap between the plasma and central solenoid, which is a challenge for the ST configuration), X-point locations, and strike point locations, enabling repeatable discharge evolutions for scenario development and diagnostic commissioning.
Type:
Dataset
Issue Date:
March 2018